Help i need help installing my Technics Reciever SA EX 510 to my Technics Eq SH GE 70 and my tape deck RS TR 272

You'll need 4 connections total. On my integrated amp, I connected the four connections to all Line In and Line Out ports. And the other ends into the tape 2/EXTRA ports respectively.

the amp should have an in and out for the cassette player also,, so you would go from the Out on the receiver, to the in on the cassette,, and out of the cassette to the in on the receiver, I don't have nor can I locate that EQ , but basically,, you need to come out of the eq and back the same way you would a Cassette player,,

Hi,
You thinking is right,just change the belt which is smaller.

Click here.

press the synchro start button, the tape deck should now go to REC PAUSE, press the SPEED button till you get the required recording speed then press the synchro start again and it should start to record from deck 1 to deck 2.

make sure the tabs at the top of the tape you want to record on are intact,
if not just put a bit of sticky tape over holes.

hope this helps?

Yes, it is a little tricky...

1) CD Changer (output) -> CD input on Amp

this is tricky... this will allow you to record to your tape deck, and control the sound via the EQ:
2) Tape Deck (tape out / recout) -> TAPE PLAYBACK on EQ
3) Tape RecOut on EQ -> Tape 1 Playback on Amp
4) Amp Tape 1 RecOut -> Tape Deck Playback / Input / RecIn
in essence, your creating a loop starting from the tape deck, going to the eq, then to the amp, then back to the tape deck to record.

Your EQ has another set of LINE IN and LINE OUT - use the second Tape 2 on the amp to create another loop. This will
allow you to control the EQ for any of the other sources.
5) LINE IN on EQ -> Tape 2 RecOut
6) Tape 2 Playback on Amp -> LINE OUT on EQ

5) Radio Tuner (output) -> Tuner input on Amp
6) DVD/VCR Combo Output -> AV/AUX on Amp

7) PC Computer... you don't have room for this. You can either use the PHONO input, and you'll have to purchase a Line Level Phono Converter
or, get a Y cable and split the signal and share with some other source.

Hope this helps.

- OPTiC
www.djproaudio.com
www.repairny.com

the Technics SH-8058 is a beautiful unit, I got one myself for the past 20 years and never failed y EQuing the sound I want.

I am asuming, you got on your reciever TAPE MONITOR... well, the it is simple,

First, just forget about the TAPE on your Techincs SH 5058

Second, on your Technics LINE OUT, goes on your tape monitor LINE IN

and last; on your LINE IN, goes on your tape monitor REC OUT.

Now, choose you desire componet, and turn on your TAPE MONITOR on your reciever...

enjoy and have fun.

Try this: Amazon.com
http://www.amazon.com/Technics-RS-TR272-Dual-Cassette-Deck/dp/B00000K0JA

Each unit (the EQ and the Processor) should have left/right in/out rca jacks as well as L/R tape in/outs. The EQ or processor use the receiver's tape loop and then provide a tape loop to replace the one they've used on the receiver.

You plug the first unit (let's say the Sound Processor into your receiver/amp as if it were a tape deck (Processor's outs connect to reciever's tape ins (play) while the Processor's ins connect to the receiver's tape outs (record).

Then you chain the EQ off the Processor in the same way (EQ outs connect to Processor's tape ins (play) and EQ ins connect to the Processor's tape outs (record).

Last you connect the tape deck to the EQ as follows. Tape deck outs connect to EQ's tape ins (play) and the tape deck ins connect to the EQ's outs (record).

This will put both the Sound Processor and the EQ in the receiver's tape loop. In order to have all the receiver's source signals routed through them you may have to engage a Tape Monitor switch or button somwhere on your amp which will route the tape loop to your speakers.

a system remote is the only option for you here. The deck does not have its own remote receiver. Sorry to break the bad news to you.