Question about Dryers

1 Answer

Dryer code 60

Gas dryer starts stops after a few minutes. Looks like b0 or 60

Posted by james Mooney on

Ad

1 Answer

AJ Yadav

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Master
  • 515 Answers

Posted on Jul 12, 2017

Ad

5 Related Answers

Anonymous

  • 12 Answers

SOURCE: Dryer stops after 5 minutes

dryer moter is covered with lint and over heating.if the moter is not completely burned out `you mite clean it with air pressure .if it still does it `replace it.

Posted on Feb 28, 2008

Ad

Anonymous

  • 525 Answers

SOURCE: Maytag MDG7600AW Gas Dryer heat starts and then stops

Warning! To avoid personal injury or even death, always disconnect your appliance from its power source--that is, unplug it or break the connection at the circuit breaker or fuse box--before you do any troubleshooting or repair work on your appliance. Also, because some components may have sharp edges, use caution while working on your appliance.

This link, http://www.repairclinic.com/SmartSearch/SmartSearch.aspx, provides exploded view imagery, belt routing diagrams, parts imagery and function, parts ordering and shipping information, error code details, just about anything you need to get your appliance up and running again. Just follow the links to navigate through the site.

You will need to enter the model number stamped on the manufacturers product information data tag, located on the unit, and not in the User’s Manual. to access your product information.


Here are some common solutions to help resolve the issue with your appliance. Clicking on the underlined links will take you directly to that page.

If your dryer doesn't heat properly, check this: Venting restriction: Disconnect the dryer temporarily from the vent. If the flame stays on for a longer period, you may have an air flow obstruction to the outside. Gas valve coils Watch the igniter. Does it glow bright orange, then shut off without igniting the gas? (When the gas ignites there's a large blue flame.) If so, there may be defective coils on the gas valve. Mounted on the top of modern gas valves, there are black electrical coils. The coils, when energized, open the gas valve. If one or more of the coils are defective, the valve doesn't open and the gas cannot ignite. Because it's often difficult to properly test the coils, it's usually best to replace both (all) of them at the same time. Also, in your case, the coils may work fine initially, but heat build up can cause the coil(s) to malfunction and when they cool down will work again.
http://www.repairclinic.com/SmartSearch/SSPartDetail.aspx?PartID=3479&PPStack=1

This link will help you with disassembly and diagnostics diagrams.
http://www.repairclinic.com/0100_17.asp


If my assistance helped resolve this issue, please show your appreciation by rating how effective my advice was in resolving this issue.
Thank you,
Dave E. (Illeagle)

"Your satisfaction is my personal reward"




Posted on Jul 09, 2008

Anonymous

  • 1028 Answers

SOURCE: Dryer heat shuts off after a few minutes.

replace the 2 black solenoids on the gas valve ..after heat up they sometimes will go bad and burner will not reignite even though the ignitor glows

Posted on Sep 24, 2008

Gigatech

Rafael Ortiz

  • 259 Answers

SOURCE: Christie DS+60 projector turns off spontaneously

Here is a list of error codes for your unit:
12 Software bug. Contact dealer/factory.
13 Flash memory corrupted. Download new software.
14 Engineering only programming is complete. Call Christie, replace TIPM.
15 Attempting to download code without being in boot mode
16 Invalid interrupt. Power off/on. If it persists, contact dealer/factory.
17 Forced boot mode. Keys held down too long.
18 Attempting to program boot mode without jumper
LAMP FAILURES
21 Lamp compartment too hot
25 Lamp 1 not installed
26 Lamp 1 Interlock: door open, lamp not installed
27 Unable to turn lamp 1 ON
28 Lamp 1 shut off unexpectedly
29 Lamp 1 driver overheated
2A Lamp 1 driver operation error (e.g. too hot can’t start)
2C Lamp 1 driver UART communications failure
30 Lamp 2 not installed
31 Lamp 2 door open
32 Unable to turn lamp 2 ON (unknown reason)
33 Lamp 2 shut off unexpectedly
34 Lamp 2 driver overheated
35 Lamp 2 driver reports operation error (e.g. too hot can’t start)
36 Lamp 2 driver UART communications failure
37 Lamp Watchdog Tripped – Unless lamps turn on again after 3 minutes, assume software hung.

Posted on Feb 26, 2009

EllaWatson25

Ella Watson

  • 725 Answers

SOURCE: maytag gas atlantis dryer. It starts but after a

I love the Maytag Atlantis!!! This sounds like your motor may be bad. It's NOT the element or it would not heat at all. Hope this helps!

Posted on Aug 14, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a DV42H5400 dryer less than a year old that runs for a few seconds than stops. No error code but the cooling light flashes. After a few minutes it repeats the process.


Clothes Dryer Stops and Starts ' HomeTips

www.hometips.com/repair-fix/clothes-dryer-stops-and-starts.html
Apr 23, 2015 - The dryer's heating element works and the motor runs smoothly, But it... and then running the dryer with nothing inside for a few minutes-if it ...

Sep 26, 2015 | Dryers

1 Answer

Ge adora dhdvh66ghobb stops heating after 8 minutes


bad thermostat possibly, which will do that

May 05, 2014 | GE DHDVH52GFWW Gas Dryer

1 Answer

Gas Dryer not working properly


bad thermal sensor needs to be replace. But not available. sorry

Jun 07, 2012 | GE Dryers

1 Answer

Have had a repair man out 3 times. Replaced igniter and gas regulator. Dryer will heat for a few minutes then stop heating. When I try to turn it back on, it will not turn on at all for about 10 minutes.


Are you saying the dryer will not start again after a few minutes? That is a motor [problem. Replace motor.
Are you saying dryer starts after a few minutes but will not heat? That is an air flow problem or a gas valve coil problem. Thoroughly clean EVERY single air passage in the dryer and vent tube. If that does not cure it, then replace gas valve coils if the igniter comes on and off.

Jul 02, 2010 | GE DCVH515GF Gas Dryer

1 Answer

Dryer stops after a few minutes of a full load.


You will have to replace the moisture sensor. The heat from the small fire may have damaged it. It's not that hard to do, but the part costs @$60.

Dec 16, 2008 | Kenmore Elite HE4 Electric Dryer

1 Answer

Dryer heat shuts off after a few minutes.


replace the 2 black solenoids on the gas valve ..after heat up they sometimes will go bad and burner will not reignite even though the ignitor glows

Sep 23, 2008 | Dryers

1 Answer

Dryer problem


Hi. thanks for the question . It looks like you have a faulty motor . I would replace the motor , thanks the appliance doc

Sep 20, 2008 | Kenmore 72802 Gas Dryer

Not finding what you are looking for?
Dryers Logo

Related Topics:

482 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dryers Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Brad Brown

Level 3 Expert

18397 Answers

Are you a Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...