ERROR C41 COPIER DOZ'NT GET READY FOR COPYING.

C41Fuser theWhat does c41 mean C41 is fuser error...u can clear it using 08-400, reset any value to "0" ...If occur again, u need to check the fuser unit, especially themistor.

Hi
The error means that the thermistor or heater abnormality at power-ON.
i think you should contact the provider.
Error Codes Toshiba Studio 167 Code C41

C41 is fuser error, enter 08-400 to clear the error, if still persist, check the fuser unit especially thermistor, heater lamp...

It depends on the model but many times the C41 error code is Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse problems.

All error code soloution of fuser unit Fuser Unit Error Status Counter
Purpose
When a fuser unit related error (error code C41, C43, C44 or C45) occurs, the set value of the fuser status
counter varies, depending on type of error.
Displaying and checking the set value of the fuser status counter can analyze a cause for the error. If
any of "2 to 9" is set at the fuser status counter, the fuser unit will not be operated for safety reasons.
After the fuser unit related error is resolved, if "0" is set, the fuser unit will be operated as usual. If any of
"10 to 19" is set at the fuser status counter, the fuser unit will be operated as usual, even if "0" is not set
after the fuser unit related error is resolved.
C41: Thermistor or heater abnormality at power-ON
C43: Thermistor abnormality after abnormality judgment
C44: Heater abnormality after abnormality judgment
C45: Thermistor abnormality during printing
C46 to C49: Reserved
Description
When this code is used, the current set value of the fuser status counter is displayed. Only "0" can be
manually entered, in order to restore the fuser unit to its normal operation, after the fuser unit related
error is resolved.
For further reason why the counter value differs despite the same error code, refer to 5.1.7 or 5.1.8
[Fuser unit related service call] in the Service Handbook.
0: No error 10: C47 (Reserved)
1: C41 (Once) 11: C47 (Reserved)
2: C41 (Consecutively occurs) 12: C48 (Reserved)
3: C46 (Reserved) 13: C49 (Reserved)
4: C43 14: C47 (Reserved)
5: C44 15: C48 (Reserved)
6: C45 16: C49 (Reserved)
7: C44 17: C47 (Reserved)
8: C45 18: C48 (Reserved)
9: C44 19: C49 (Reserved)
* Default: 0
Setting Timing
Use this code to resolve the fuser unit related error (error code C41, C43, C44 or C45). Resolve the
error, and set "0" (or reset the counter), in order to restore the fuser unit to its normal operation.
Caution
Remember to resolve the fuser unit related error, and then reset to "0."

I suppose the error code is C410.
To clear the error message, perform 08-400 => 0.
If happen again, u need to check the themistor.

C41 is fuser error...
u can clear it using 08-400, reset any value to "0" ...
If occur again, u need to check the fuser unit, especially themistor, themostat and etc...

I have a TOSHIBA photo copy machine 2860 whic shows a red wrench error

Reset the status counter
(1) The following processes are carried out after completing repair of the cause for the C41 error
message.
(2) Press the [0] and [8] keys simultaneously to turn on the power.
(3) Input 400 using the numeric keys, and press the start key.
(4) Change the displayed status counter from [2] to [0], and press the SET key (Reset C41).
(5) Turn the power on again, and check that it returns to the normal standby mode.

Let me know your result.

Hi,

 C41 refers to Poor contact of the fuser drawer connector.
 Fix it!!!!