Reset pin DECT 6.0 - Dect Lands Phones

check settings and switch off fax mode

For the Uniden DECT 6.0 6035 system...

Setting a Security Code or Personal Identi?cation Number (PIN)

To play your messages from a remote location, you will need to enter a two-digit security code or Personal Identi?cation Number (PIN). The default security code is 80. To change the PIN:

1) On the handset, press [Menu/Select]. Select the ANSW. SETUP menu, and then the SECURITY CODE submenu.

2) Use the number keypad ([0] through [9]) to enter a two-digit security code (00-99).

3) Press [Menu/Select]. You will hear a con?rmation tone.



Here is the manual:
Uniden 6035 1 Owner Manual

Sherry:
I believe that some how the security code #99 got changed. You may want to reset that code as #99 no longer works. From the manual:

Setting a Personal Security Code (PIN)

If you want to be able to play your messages from a remote location, you need to enter a two-digit Personal

Identification Number (PIN) code (01-99).

To select a PIN, perform the following steps:

1) With the phone in standby, press [menu/clock] twice.

The system announces "Security code," and the current PIN code is announced as it is displayed on the base.

Then the system announces the instructions for setting the PIN code.

2) Press [volume/select/ ] or [volume/select/ ] until the desired number appears.

3) Press [set] to select the PIN code. You hear a confirmation tone, then the announcement "Security code"

followed by the new PIN code is announced. After a few seconds, the system announces "To set ring time, press

menu again."
Note: The PIN code is set to "80" at the factory.

What model AT&T DECT 6.0 phone?

Sit the headset units back to the main base one by one.
Make sure you do all of them at the sametime.
This will reset the DECT 6 security feature.

Swap out the rechargeable battery to rule out weak battery problem.

Since you declined to specify the model of your Uniden DECT 6.0 system, I can only suggest that you select it from the list beginning here to download the manual. The manual will tell you how to change the PIN and set up the voicemail system.

Since you neglected to specify the model of your Uniden DECT 6.0 system I can only suggest you select it from the list beginning here to download a copy of the manual.

Since you declined to specify the model of your VTech DECT 6.0 system, I can only direct you to enter it into the search box here to download a copy of the manual.

unplug the base then hold the register button (the round one on the left of the minus sign) plug the base in while holding the register button for at least two seconds till you hear a beep. the pin will be reset to 0000.

[ARC20x User Guide p20: 11 Handset Registration]
To register a new handset:

1. Press and hold the HANDSET LOCATOR on the base unit until you hear Registration tone (repeated 'beeps')
2. On the handset, press the PROG then the UP or DOWN button to display "REGISTER"
3. Press the PHONE/OK
   -> The display shows "BS 1234". If any of these numbers is steady (not flashing), then the handset is already registered to that base unit.
   
4. Press 1 to select base unit number 1
   -> The display shows "BASE PIN _ _ _ _"
5. Key in the system PIN (default 0000) and press the PHONE/OK
   -> The display shows "WAIT _ _ _ _" for a few moments, while the handset searches for a base. Then it shows a list of handset numbers which are still free on the base unit.
   (For example, "1 34 6" indicates that numbers 1, 3, 4 and 6 are free; 2 and 5 are already assigned to other handsets.)
6. Key in a free handset number
   -> After a moment, the display should show the handset's name and number.

If registration fails...

• Try again, making sure you begin step 2 as soon ans Registration tone starts.