Toner light flashing in printer 330

Solution: If you replace the toner cartridge and the 'Toner Low' message remains, the printer may need to be reset.
To do so, power off the printer. Let it sit 20 to 40 seconds, then power it back on. If the 'Toner Low' message does not appear on power-up, try printing again.
If the 'Toner Low' message returns on power-up or when printing, confirm the following:

• The toner cartridge you just installed is a brand new toner cartridge and not a used one.
• The toner cartridge is an original Lexmark brand toner cartridge. Cartridges manufactured by a third party may not be compatible with the printer.
  If a third-party cartridge is causing this issue, contact the point of purchase for additional support or replacement of the toner cartridge.
• The toner cartridge has not been refilled or refurbished by a third party. If it has, contact the place where it was refilled to have it replaced.

Still Need Help? Should you confirm all the above and the 'Toner Low' message remains, have the following available when calling Lexmark Technical Support;

• Printer model(s)
• Printer serial number
• Toner/imaging unit/waste toner bottle part number and serial number

If the blinking light is on Toner Low (4th light starting from left), press and release the Continue button (green button) to clear the light sequence and continue processing the print job. If the light is still blinking, the photoconductor is almost full and should be replaced.

For further assistance, please contact Lexmark Technical Support

The flashing toner light indicates that the photoconductor kit needs to be replaced.
Use this Lexmark Part# : 12A8302 to order. After replacing the drum cartridge counter will have to be reset, Use the following steps.
1. Open the front door (press button on left side).
2. Press and hold the cancel button (x button) until all the lights flash in order.
3. Then close the front cover.
This will reset the drum counter to enable continued printing.

error light on out of paper also toner light is flashing but its a new toner kit and there is no paper jam

Could be photoconductor at end of life.

You shoul still be able to do a printer test print (press the arrow button).

Look on the printed pagesfor Toner AND Photoconductor.

These show as OK when new or very low count, and 100% when fully used.

If the toner is showing as 100% when you've just replaced it, either the chip is faulty, the wrong one, or if the cartridge is a remanufactured one possibly nor been replaced.

The Photoconductor Kit designed for use with Lexmark E230, E232, E232T, E238, E330, E332, E332N/TN, E240, E340 and E342. Yields 30,000 pages.

Have you printed 30,000 pages on this unit? If not perform the following reset:

Procedure for E-232 is:
1. press and hold Start
2. turn on the printer
- this is service mode -
- by pressing the Start you can print Printer Settings Configuration sheet -

3. press and release Cancel 4 time
4. Press and hold Start while all lights start cycle
5. press and hold Cancel untill all the light cycle
6. turn the printer off to exit the menus

If I could be of further assistance, let me know. If this helps or solves the issue, please rate it.
Thanks, Joe


I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_8b8c2cd6ce148309

wow, yes.. press the Grey button on the side and the printer front mouth will open, than press the Grey button on the bottom left side down and take out the cartridge by pulling it with the handle....

Use this link it might help your problems::

http://support.lexmark.com/cgi-perl/knowledgebase.cgi?ccs=229:1:0:570:0:0&framed=&docid=ENUS25374&relevance=1

1- you either got a bad toner ( the chip on it is telling it it is bad)

happens sometimes with recycled toners.

Return it and tell them it is defective.

The chip needs to be replaced.

 

Try this but doubt it will work,

open front door hold down go button, all lights will flash in sequence wait for it to stop turn off and on and close door.

Try resetting it, open front cover hold down silver button, all lights should flash rotatingly, when stopped turn off and on and close door.