Question about Televison & Video

1 Answer

I have a Tesco hudl 2 that has a broken earphone jack stuck in its earphone socket. I read somewhere that you can get round this by connecting the hudl to a bluetooth speaker but I still get no sound.

The two appliances acknowledge that they are connected to eachother, but I suspect I'm not getting sound because the jack plug is switching it off. Is there and ay round this i.e. can I set the hudl to transmit to bluetooth even with the jack plug in?

Posted by John Smith on

Ad

1 Answer

JonSnell Electronic

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Televison & ... Master
  • 31,793 Answers

The headphone socket contact mute the sound.
Replace the socket.

Posted on Sep 04, 2018

Ad

5 Related Answers

Anonymous

SOURCE: Connecting a laptop to car sound speakers

maybe , that is what i a asking, i don't know

Posted on Jul 31, 2008

Ad

Anonymous

  • 7 Answers

SOURCE: Connecting Sony PS2 to Panasonic HT32LZD85

First off you need to retire that ps2 and join the PS3 revolution, well worth the money although with the recent drop of the inferior x-box 360 the PS3 may follow suit shortly.

Now, I'm gathering from your discription limited as it may be that you had an adapter that connected the the stock cable that was included with your ps2 which consists of the end that interfaces with the ps2 and the end that is ment to provide the signal to your tv which includes your composite video (yellow) and your left and right audio (red&white).

If this is case then it should be a simple matter of removing the adapter that changed the source (ps2) signal to aerial and pluging the yellow red and white cables direct to your tv (standard imputs at the rear of the television should be video 1,2,3 ect.

Then just make sure your tv is on and set to the correct imput and you should be rockin and rolling in no time.

Posted on Oct 03, 2008

Anonymous

  • 38 Answers

SOURCE: External Sound Card

No, that's not going to work. Digital output is just that....Digital. Your trying to send a digital into analog....won't work. Your tv don't have red and white audio out. That's what you hook to, but it still wouldn't be 5.1. Your out of luck my friend. The ONLY way you'll get 5.1 out of that T.V. is to get a 5.1 reciever with CO-AX digital input...the SAME as whats on your T.V. You can only hook-up sound to your X-FI with the line in jack using a y-connector and 1/8" stereo plug....and it won't ever be 5.1. It can't that way. Only way to get 5.1 to work on the blaster is with the tosh-link optical input cable. This too is digital, but uses optics to send it. Remember, you are playing with 2 different formats. Analog with your white/red thing you made and then digital. Digital using co-ax or optical tosh-link. Completely different.....as you now know.

Posted on Dec 05, 2008

Anonymous

  • 5 Answers

SOURCE: No sound from external speakers system

Look into your monitor settings and computer settings and see if you can reverse the "input" and "output". If both are set to line in or line out then they pretty much cancell themselves out.

Posted on May 23, 2009

Anonymous

  • 1 Answer

SOURCE: Sony KLV-26U300A + xBox 360 setup help needed!

SHEARCH eeprom memory dumps

Posted on Jun 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No sound on my technika 42" 3dtv


If the headphone jack socket works the audio output for the set is good, I suspect a dvd etc will also work if connected to the rear input audio and video jacks.

This does not leave too much, headphone jack dirty or defective, speakers for whatever reason are switched to off in the main menu.

the sound for the headphone socket if it is built into the set is the same audio going to the speakers.

Dec 05, 2012 | Televison & Video

1 Answer

MARSHALL FOOTSWITCH FOR DSL100 TROUBLES


Does your M foot switch work on the Fender? If you know how to use a multimeter you could check continuity by putting meter leads on plug of M foot switch(1 on tip, 1 on sleeve ) You should see a change in the multi meter when you depress switch. If so switch is good. Another easy test is with cap off a spare 1/4 plug -plug it in to foot switch jack.put a alligator or some such metal clip or wire and join(called short or shorting) the two inputs . If connecting and unconnecting results in switching then the foot switch is suspect. One fairly common thing is that foot switch and input jack are often sautered straight to a circuit board to save $ on production cost. Used to be all point to point where a wire was attached to 1/4" input and then wire went to circuit board or tubes. The wire has give, but not so with direct wiring to board. So the nut holding the 1/4" amp input gets loose(doesn't have to be loose for the following to happen) and a pull on the chord causes a break in the soldier and thus a break in the sound chain. Sometimes it will work intermittingly by putting a little pressure left, right, up or down on the plugged in plug. If so, it's the input jacks connection to the amp. If not it still could be that because putting pressure on plug may not be sufficient to affect a temporary reconnection. Since switch(the new one you made)works on Fender, but not Marshall I suspect the jack or foot switch circuitry past the input jack. If using some of the above the above tests leads you that direction,remove housing(unplug a/c power 1st ) inspect jack,wiggle it slightly see or feel a break then resodier from back side. You should be able to use the soldier already present without adding extra.

Sep 27, 2017 | Music

1 Answer

Getting distorted sound when connecting from mac pc headphone jack to 1/4" line in input


You are connecting a NOISY unbalnced line to a balanced input. Buy a DI box and then use an XLR to XLR to the mixer inout and run the MAC into the DI with "ground lifted". You will need to make a resistive mixer between the headphone jack and the DI as well. The headphone jack is STEREO. You COULD try a STEREO 1/8 inch splitter to 1/4 inch left and right cable... you MIGHT get away with that. Right now the left and right amps in the MAC are fighting eachother.

Sep 25, 2011 | Samson New Samson Mdr-1064 10 Channel...

1 Answer

I have a Latitude D600 laptop. When I plug in my headphones, the sound still plays through the built in speakers. When I twist the plug in the jack I can sometimes get sound in the headphones but it still...


I dont think the JACK is the problem, I suspect a bad headphone wire (intermittent) or an incorrect driver, headphone jacks in laptops are software controlled, (no mechanical switch inside) if you hear sound in both the headphones and the speakes it is a driver issue, try updating the driver, if the headphone wire is erratic it can fool the software that controlls the input and do crazy things also...

Good luck!

May 26, 2011 | Dell Latitude D600 Notebook

1 Answer

Spark plug change on a 2002 carrera 911


jack up rear of vehicle install jack stands, get under car posche's have a boxer engine (opposed cylinders) they face eachother, so the spark plugs go three on one side three on the other unplug and remove all six ignition coils, remove spark plugs I usually have to use multiple extensions on my plug socket and put them together while sticking them in the holes because its a tight fit.

Mar 02, 2011 | 2002 Porsche 911

1 Answer

I have a Roland FP 1 digital piano, serial #AL21141N. It has gradually quit putting out sound through the speakers. At the onset of the problem, I could fit it by jiggling the 1/4" speaker plugs,...


I first would suspect the switches on the eadphone jack. Normally these cut off the speakers when headphones are plugged in. These jacks and the switches are really weak, poorly made, and easily broken, especially if headphone cord gets yanked.

Jan 14, 2011 | Roland Digital Piano FP4 Black With Stand...

1 Answer

I have a Marshall MG100HDFX 100-Watt Amplifier half stack (solid state) and I now am not getting ANY sound out of the amp. I changed the fuse and the power module behind the fan, and still no sound,...


plug headphone in the effects send jack...If you get somme sound (won't be too loud) there, that means preamp sections are probably ok. Drive a signal into the effects return jack... If power amp responds, it is OK... If both these are OK, then suspect the switch contacts on these two jacks that forward the preamp to the power amp when effects unit is NOT plugged in.
These contacts are a chronic problem.

Sep 19, 2010 | Marshall MG100HDFX 100-Watt Amplifier Head

2 Answers

Can't get the tv to play through the home theater


No they all are compatible with eachother no matter what brand tv,surrround sound. It is all in the hook up & without you stating how you have it hooked up,no way to tell because one siimple connection is all you r missing. You have it most way there if sound is ok on dvd.If you explain how you have it hooked up i can surley help you!!

Jan 23, 2009 | RCA L32HD31 32 in. LCD HDTV

1 Answer

Thinkpad- interferance


You should put or connect a ground line from your stuff connecting to the ground to eliminate noise.

Jan 17, 2008 | IBM ThinkPad T43 Notebook

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

187 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76407 Answers

Cindy Wells

Level 3 Expert

6133 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...