Question about Briggs Garden

1 Answer

Pressure Washer Replacement Pump will not turn when installed on the Briggs shaft.

Replacement Pump RMW 2.2G24 is tight when in my hands. I installed it and cannot turn the motor. What is preventing the pump from turning?

Posted by Dennis Weinhold on


1 Answer


  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.


    An expert that got 20 achievements.


    An expert that got 10 achievements.

  • Briggs Master
  • 85,239 Answers

Does the pump turn freely when it is not connected

Posted on Nov 11, 2016


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Ball valve spring pressure washer detergent line

Not sure what type pump you have but you can buy a chem. injector rebuild kit at Pressure washer parts catalog quick links Pressure Washers High Pressure...
If you need to replace the spring then replace the entire kit. Ball, spring and oring. Most pumps that come on the newer TRoy bilts are AR RMW pumps. the parts diagram can be found here at
The parts for a AR chem. injector are
480480 O-Ring
1250280 Ball
1560520 Spring
Good luck

Jul 22, 2014 | Troy-Bilt 020528 Gas Pressure Washer

1 Answer

How to fix power washer with no pressure with out have to buy the hole pump what can i do to fix it

Cover soap inlet and retry. Mine will not pressurize without soap or without inlet covered.

Jul 22, 2014 | Annovi Reverberi Garden

1 Answer

High pressure wont shuy off

do you mean it keeps trying to build pressure even when you release the trigger on your wand???that is a problem with your unloader....also checkout your shutter valve and replace the oring on it. You will need the diagram here to know what parts Im talking about Pump Breakdowns and you can order parts here Pressure washer parts catalog quick links Pressure Washers High Pressure...

Jul 19, 2014 | Annovi Reverberi 2400 Ar Pressure Washer...

1 Answer

Low Pressure

Very little info to go on here. Could be a valve issue or a packing issue or an unloader issue. If it has been sitting for any length of time which tends to be the case, then an unloader valve is most likely the culprit. Good luck

Apr 19, 2014 | Annovi Reverberi Rmw 2g24 Vertical Shaft...

1 Answer

Oil capacity on rmw 2.2g24

4.5 ounces
Changing the oil in the pumps is not required but if you need to then Ar makes its own oil for the RMW pumps. #64545

Apr 06, 2014 | Annovi Reverberi AR RMW2.2G24EZ-SX...

2 Answers

How do you install the pully onto the power steering pump?

Find an all thread bolt that is about 3" long that will screw into the pump shaft. You will need a nut and a washer that fits the bolt. Put the nut and washer on the bolt,Set the pulley on the shaft and screw the bolt in the shaft as far as it will go hand tight, but at least 5 or 6 revolutions. you willneed two wrenches , one to hold the bolt and one to turn the nut. The pulley must be flush with the shaft when you are done

Nov 24, 2010 | 1996 Plymouth Voyager

1 Answer

My Husky pressure washer 2600 psi powered by a gcv 160 Honda. Engine starts no pressure other then from water source and soap is not being dispensed

It sounds like the (RMW 2.2 G24) pump has gone out. Mine had this problem after about 6 hours of use. I was able to order a new pump for around $160.00, and then installed it myself. Go figure it was just out of warranty. I think my next pressure washer will be one with a professional pump as I was told the one on my husky is only rated for about 40 hours of use.

Jul 10, 2010 | Garden

Not finding what you are looking for?
Garden Logo

Related Topics:

253 people viewed this question

Ask a Question

Usually answered in minutes!

Top Briggs Garden Experts


Level 3 Expert

4369 Answers

John Trevino

Level 3 Expert

1420 Answers


Level 3 Expert

85239 Answers

Are you a Briggs Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides