ERROR E000004-0401 ON CANON C4080i WHAT DOES THIS MEAN

Solution 1: Replace the Waste Ink Absorber
Step 1: Press the Power Button
* With the Canon Printer Powered off but connected to a power source. Press the "Power" button while pressing and holding the "stop/reset" button.
Step 2: Press the Stop/Reset Button
*When the Power is lit, press the "Stop/Reset" button two times
*While pressing and holding the "Power" button
Step 3: Move Into a Service Mode
*When releasing the "Power" button and the "Stop/Reset" button (regardless of order), the printer will move into a service mode. (waiting for menu selection)
Step 4: Press "Stop/Reset" Button
*When the on/off lights in green, press the Stop/Reset button the specified number of time(s) according to the function listed in the table below.
(Each time the "stop/reset" button is pressed, the LED lights alternately in orange and green, starting with orange)
Note: Make sure there is need to press 4 times for waste ink counter reset
The number of the Reset button pressing LED Function Remarks
*0 time Green Power off
*1 time Orange Service pattern print
*2 times Green EEPROM print
*3 times Orange EEPROM reset
*4 times Green Waste Ink counter reset

Step 5: Turn on Canon Printer
Turn off the printer, then turn it on again.

Now Check the Canon printer error code 5800 is resolved. If not, then go to the next solution.

Solution 2: Enter Canon Printer in Service Mode, works best for multifunctional printers.

Step 1: Turn Off Canon Printer
Step 2: Go to Press the Menu Option
Step 3: Put Printer in Service Mode
*To do this you will have to press the "SCAN", "COPY" and "SCAN" buttons in that exact order.
Step 4: Reach to the "Counter Access" option
Step 5: Check amount of pages that you are printed
Press the "ok" key
Step 6: Press the "COPY" Button
Step 7: Score all the way to zero
Step 8: Stop once get "Scan Page Count" Option
Step 9: Set Score back to zero
Step 10: Press the "STOP/Reset" button
Step 11: Turn Off "Stop/Reset" button
Step 12: Disconnect the Power Cables and reconnect

Dear kindly reset the printer to its factory default setting.

upgrade the sdRam up to 1gb to solve that problem

Try safemode with networking

not work, in display printer shows error 5b00. I can't go to nv ram setting. Can you help me?

I think that error code means a problem with the scanner/lamp. Any type of Exxx code means the machine needs (repair) service. This is a fairly new product and should still be in warranty, so I recommend you contact your regional Canon service agency.

Hi,

The error code means "Ink Detection Waste Ink Tank Full". This means that the ink pad needs to be replaced. Also, dont forget to set the eepron counter to 0. Please follow the steps:

Press

ADITIONAL FUNCTIONS
SCAN
COPY
SCAN
scroll to TESTMODE
scroll to PRINTER TEST
scroll to EEPROM CLEAR
and the press the numeric key 3 or and keys.
Select INK COUNT, and then press the
numeric key 0 or and keys to reset the waste ink capacity.
Press the [Stop/Reset] key and then the
[ON/OFF] key to end the test mode.

I tries to replicate this error in my printer and I was able to aolve it with the above mentioned steps.

Hope this helps!

Rehards,
HP

5100 means either there is paper stopping the carriage from moving properly, or there is grease on the plastic strip behind the carriage. If you wipe off the grease with a Q-tip the error will go away.

The drum will either produce an error code of E000020 with multiple subcodes. This is time to change it. Also if your getting weak density or solid backgrounding of a particular color. These are all ques to change the drum.

As long as it is a proper ground and a 15amp service it should be fine. On all color copiers I would reccomend that you install a line conditioner (it is a surge supressor plus it filters line noise).
a line conditioner will add a longer life to the copier.