Question about Lutron Electrical Supplies

Open Question

Luton lights switches don't work in most of the house.

We have a Lutron lighting system which was installed in 2008, I am not sure which system it is. Last night when we went to turn on the lights, they would not go on (except for the bedroom/bath control), unless we went into the switch in the garage and pressed "Home" in which case certain lights went on. When we press any of the switches the house (again, except for the bedroom/bath), they just blink and the lights will not goon.

Posted by Lynn Arnhold... on

Ad

5 Related Answers

Anonymous

  • 19 Answers

SOURCE: Connecting Leviton Decora light switch.

At the switch you have a feed wire coming in this brings in power which originates in the electric panel. You also have a feed or feeds goings out to other lts or switches, this you seem to have on the switch. instead of the closet switch loop.undo all the wires. find the only hot this is the one wire you can touch to the others and make different lts come on i reccomend getting a electric tester to do this. FInd the wire that goes to the closet lt. Once your sure put it to the side. wirenut all other wires together with the hot wire. this makes all other switches independantly hot. connect the hot to the switch and the closet lt to switch. I HOPE THIS MAKES SOME SENSE TO YOU . let me know if i can help

Posted on Jan 04, 2009

Ad

dennis bullard

  • 4090 Answers

SOURCE: putting outside lamps on exterior on timer

why not connevct them up to a movement sensor, that way they come on when you make a movement near them. So they dont fire off when cats or birds fly by make sure you set them to close to your height. Then you can see your way to the shed turn the lighjt on that you can now see where the switch is and then turn it back off when you leave. Most of these sensor lights can be set toa timed on period

cheap and easy to install

Posted on Jun 22, 2009

Ad
CaptAdams35

Christopher

  • 28 Answers

SOURCE: triple rocker switch to control 3 function bathroom fan/light

I suggest you cut 3 pigtails out of your black wire (about 5-6" each and strip them so you can put a nut to tie them all together on the main wire, then do the same for your grounds using green 5-6" strips of wire and then connect all 3 switches with the pigtails to their proper locations. This WILL fix your problem.

Posted on Mar 09, 2010

Anonymous

  • 1 Answer

SOURCE: Replacing old light switch, only use copper wires?

house wired in aluminum

Posted on Apr 29, 2010

Anonymous

  • 3 Answers

SOURCE: not sure how to wire this switch

Switch will have a commom terminal that the hot wire connects to.
The other three terminals are for the devices -- light, fan and other device.

The white wires should be the grounded wire returns for the circuits unless they are identified by color tape to be hot line side of power.

Be careful of the grounded side of circuit, can shock or kill, treat all wires as being energised. If you are not sure, use a electrical tester,
or get help.

Posted on Jul 22, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Volvo c70 battery keeps going flat, its a new one ,and had it tested theres no drain. i turned the light swutch to 0.at night is this right the car is new to me


is the alternator charging. if it is then. I am guessing a light is coming on after you walk away. my truck did that. 2 hours later the lights would come on

Feb 11, 2015 | 2008 Volvo C70

1 Answer

I had an electrician over to replace some low-voltage light bulbs that were too high for me to reach, and also a couple for which changing the bulb didn't work. He changed the bulbs and left one with...


I do not know what happened.
Check the circuit breaker.
The electrician is probably asking somebody else right now, because tradespeople want to know everything about their trade to expand skill and make money easier.
Lutron has customer support number for you and the electrician:
1-800-523-9644
Calling Lutron might narrow down what product you have, and isolate problem.
Once exact product is known, this will be helpful for the electrician.
Plus you can re-post a question on fixya, and expert will look up that product and give possible help. This will also help you double-check the electrician.
Between Lutron, the electrician, and fixya, a solution is probably reachable.

Jul 14, 2011 | Lutron Electrical Supplies

1 Answer

Night light in lutron wall switch flashing can it be fixed and how


Unfortunately, no. Its a neon bulb that gets soldered into the product, so its not something that can be tweaked or replaced. My suggestion would be to call their tech support number 1-800-523-9466, and see if you can get them to replace the whole dimmer.

Nov 10, 2010 | Lutron Almond - Diva Incandescent Dimmer...

1 Answer

How to install


Lutron S2-LFSQ is made to control one ceiling paddle fan & 1 light. Switch will not work on florescent lights.
See manual

To use this product, your fan and light must already be controlled by 2 separate switches.

If you have just one switch that turns on the light & fan together, the S2-LFSQ will not work (without additional wiring).

Okay, you have two switches. One switch turns fan on-and-off. The other switch turns light on-and-off.

Here is wiring diagram from manual: See diagram larger

8263536.jpg

Here's how to wire:
-Before disconnecting wires from existing switches, mark each wire with tape and pen.
-There is one wire that feeds power to both switches > mark this the 'Hot wire' and it connects to Lutron black wire (if you are unsure about this wire, remove switches, separate wires, turn on power and test each wire to bare ground, tape tester leads to wood sticks so hands are away from power, Tester lights up on Hot wire)
-The switch that controls fan > mark this the 'Fan wire' and it will connect to Lutron Yellow wire
-the switch that controls light > mark this the 'light wire' and it will connect to Lutron Red wire
-Lutron Green wire or bare wire connects to bare ground wire.

Oct 02, 2010 | AMS Lutron S2-LFSQ Skylark Dual...

1 Answer

Our dimmer switched worked perfectly last night and this morning. This afternoon when I went to turn the light on it didn't work. It works if you manually hit the up or down button on the side. However,...


sounds like an internal part has broke and you will have to replace the whole switch. anytime you have trouble with something like that it is always best just to go ahead and change it. it doesn't if its a day old or 10yrs old. not worth the chance of burning yourself down.

be glad to help you further if you need it txt me at 865-888-1220

Jul 02, 2017 | Lutron ELECTRONICS MAW-600H-LA SMART...

1 Answer

I have just installed the Lutron Maestro® 600 Watt Single Pole Dimmer, White in my master bedroom. The outlet is connected to a ceiling fan. Every time I turn the fan off with the light on, the light will...


YOu need to make sure that the maestro you installed is designed for use with electric motors. CHeck out this page on the lutron site... http://www.lutron.com/CMS400/page.aspx?id=16955&mn=1797. THese are the dimmers you can use with a fan. If it is in the same box the magnetic interference can cause the types of reactions you are mentioning.

If this is not the problem you need more info-- is the light part of the fan, is there a separate wire for fan motor and light? what type of switch is controlling the light (assuming the maestro dimmer is controlling the fan motor etc...

Dec 27, 2008 | Electrical Supplies

1 Answer

Have a Lutron Skylark SF-10P need to wire to existing 3 wires


You have to have a special ballast on the light to dim fluorescent light fixtures. You also have to have a special dimmer.

Nov 28, 2008 | AMS Lutron SFSQ-LF Skylark Slide-to-Off...

1 Answer

Gauge light not on!


Have you checked the instrument panel dimmer switch? It is in the center of the cluster, a black round stick. It also resets the trip meters...
Turn this, and the dash lights go dim, and then out. Or, you may have a blown panel fuse.

Sep 07, 2008 | 2008 Toyota Corolla

Not finding what you are looking for?
Electrical Supplies Logo

Related Topics:

288 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lutron Electrical Supplies Experts

jdthefixer

Level 3 Expert

746 Answers

mpservices

Level 2 Expert

191 Answers

Nick

Level 2 Expert

129 Answers

Are you a Lutron Electrical Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...