Need Emerson Remote for color TV with DVD Player

Make sure tv input is set for the slot you plugged the DVD
into.On the tv remote you will find inputs.Just change for the right one.
Most of the time DVD player is working when TV is on channel 2 or 3 .

Not enough information for a good reply. Are you sure your tv is set to the correct mode or channel for vcr? Make sure both devices are on, your dvd/vcr playing if you can, and see if the tv on channel 3, channel 4 or channel 91 show that dvd/tape. Otherwise, try checking your remote control, MENU button and look for device options, or INPUT options, on the main menu.

Hello
Setup codes for Emerson Tv with One For All URC-4021 remote control are:

0154, 0236, 0463, 0180, 0178,
0171, 0623

The One For All 4 Device Universal Remote Control is preprogrammed at

the factory to operate an RCA TV, a Toshiba DVD player, a Motorola cable

box, and an RCA VCR.To control devices other than the default brands,perform
the following steps; otherwise skip this section:

[1] Turn on a desired device (e.g.,VCR or DVD player) and, if
applicable, insert media (e.g., cassette or disc).

NOTE: Please read steps 2 through 4 completely before proceeding.

Highlight or write down the codes and device you wish to program
before starting step 2.

[2] On the remote control,press a device key once (i.e., VCR/PVR,
DVD, CBL/SAT,or TV).

NOTE: To program control of a VCR, PVR (or DVR),TV/VCR Combo,

or TV/VCR/DVD Player Combo press VCR/PVR once.After programming

a VCR Combo device, you will be able to control channel selection,

volume, and VCR functions.

NOTE: To program control of a DVD Player,DVD Player/VCR

Combo, or TV/DVD Player Combo, press DVD once.After programming

a DVD Combo device, you will be able to control channel selection,

volume, and DVD functions.

NOTE: To program control of a Cable Box, Cable Box/PVR (or DVR)

Combo, Satellite Receiver, or a Satellite Receiver/PVR (or DVR)
Combo, press CBL/SAT once.

[3] Press and hold SET until the LED (red light) blinks twice,
then release SET.

[4] Use the Manufacturer's Codes (starting on page 18) to

locate the type of device and brand name and then enter

the first four-digit code for your device. If performed correctly,
the LED will blink twice.

NOTE: If the LED did not blink twice, repeat steps 2 through 4 and enter
the same code again.

[5] Aim the remote control at the device and press POWER

once.The device should turn off. If it does not, repeat

steps 2 through 5, trying each code for your brand until

you find one that works. If it still doesn't work, try
Searching For Your Code on next
NOTE: If the device does not have a POWER key, press PLAY
OK.

no you need to get a universal remote

on the front and on the back of the TV it has a set of tulip jacks a yellow one for
video and either a white or red one for audio. Take a set of RCA cables and hook them
from the DVD to the TV via the colors yellow for video red/white for sound. For this TV
I believe you will need to go throught the channels until you find composite/AUX1 or composite/AUX2 which the DVD will be assigned to. If the DVD player is on and functioning you should get a picture. If you dont get a picture and you get fuzz and buzzing on these channels you have the video and sound reversed. Some models may have a source button on the front of the TV or on the remote. If this is the case use the source button to get to the Composite/AUX channel.

IM GUESSING THIS MIGHT BE AN RCA TELEVISION? if you dont have an rca in hook up on the tv give up and buy a new tv or you can find an older item what it is is a switch that has an rca input and a coax output it was used to hook up the older video game systems it is still sold in most stores and that will work if you do have rca inputs and lost the remote you need to get a universal remote to switch the input on certain older rca tv's you could go to channel 00 and it would set it to the input with the switch you shoudl be able to use it by putting the tv on channel 3

Need the remote to go to the aux. The number for parts and service is on the back

Oh man dont shoot your stuff instead use your remote and go to your menu and select your input. You tv is looking at your coaxial input but you can select which input you want. 1, 2 front back whatever you need. channell 3 or 4 has nothing to do with connecting up your dvd if you connect and choose the front connection in your menu.

CHECK YOUR TV MANUAL FOR REMOTE INSTRUCTIONS IF STILL HAVING PROBLEMS CALL EMERSON AND TALK TO THEM ABOUT YOUR PROBLEM

hey i sort of hav the same problem except, i cant access the "channel" with my sons game stuff on it
if i click menue then it just givs me "Picture" "Channel Set" "Language" "V-Chip Set-Up" "Captions" and if i click channel set i get "CH{TY}" "CH{CATV}" "CH{DTV/TV}" and v-chip asks me for an access code. and i got this tv from a friend and he lost the remote. i only hav an iO Digital Cable remote. help me plz