Question about Makita Drills

Open Question

Makita hammer drill is not openimg .. Case is slipping around the hand chuck... Stuck in open ...

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 313 Answers

SOURCE: makita 8444d mxt drill

what is the setting in your clutch. if you set the clutch to the highest setting and it`s still slipping then you need transmission assy.

Posted on May 29, 2008

Ad

Barry Benjamin

  • 9 Answers

SOURCE: drill bit is stuck inside my makita drill chuck

Try using the low torque setting on the drill when reversing and something to assist you getting a better grip to hold the chuck from spinning when reversing. This may help.

Good Luck

Posted on Dec 04, 2008

Ad

Chuck Bamforth

  • 205 Answers

SOURCE: Stuck chuck

open the chuck all the way, insde there may be a screw in the bottom it's lefthand thread turn it clockwise to remove, the chuck is also threaded, right hand thread. close the jaws on the short end of an allen wrench and strike the long end with a hammer to break it free

Posted on Apr 03, 2009

meleemore

Anthony Smith

  • 19 Answers

SOURCE: Makita Percussion Drill HP2051F keyless chuck release problem

jacobs come out with this all metal keyless chuck(i think thats what you have) and if thats the case, there is no solution for this youll have to replace the hole chuck, being its new, it may be under warrenty

Posted on May 05, 2009

Anonymous

  • 2 Answers

SOURCE: 18v makita bhp451 cordless hammer drill.clutch

its prob stuck between gears one and two try a little wd40 on the gear selector switch

Posted on Jul 31, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Changing the chuck of a 6408 makita electric drill


Open the chuck and remove the screw inside the chuck (if fitted) the screw is left hand thread, fit the short end of the largest hex key that will fit into the chuck and tighten the chuck, put the drill into low gear and turn the clutch to the drill position, support the drill on a bench and strike the long end of the hex key with a firm blow (right hand thread) it may be neccessary to strike it more than once

Jan 30, 2013 | Makita Tools 18V 1/2" Lxt Lithium - Ion...

1 Answer

I have a Makita HP1621f Drill,and I cannot get the drill bit out,seems like the chuck itself is bad,any ideas on how to remove the drill bit?


Sometimes if you happen to have the right size bit, it will stick into the bolt that holds the chuck on if the chuck wasn't tight enought to keep it from slipping further into the chuck. Clamp drill bit in vice and tap chuck with soft hammer to pull it free.

Oct 04, 2010 | Makita & 1/2 Inch Drill

1 Answer

Bit tighten stuck open


If you mean the chuck jaws seem stuck open, spray around them with some penetrating oil or spray like WD-40, RP-7 or similar and let sit for a couple hours... Then you can tap around the chuck body with a light hammer or spanner etc... just lightly tap... Then if the chuck has an arbor lock to prevcent it from spinning, be sure that is engaged then try to release the chuck jaws. Sounds like they are stuck open through tight friction or rusting on the inside edges (that you dont see). Be careful not to leave them in the fully open position when stored as this is exactly what can happen!

Mar 31, 2010 | Makita 6304LR 1/2" Chuck Electric Drills

1 Answer

How do I remove and replace the keyless chuck on a makita hp1621F?


Remove the screw inside (clockwise)
mount a big Allen key in the chuck ,shortest part inside the chuck,
hurt the key with a hammer to make tre drill move counterclockwiseto unblock it


Nov 16, 2009 | Makita HP1621FK 5/8" Hammer Drill, 5.7...

1 Answer

Chuck jaws on Makita 8444D fell out


There is suppose to be a flat head Left hand thread chuck screw in there. It may have fallen out. You will not be able to put the jaws back into the chuck. You will have to replace the chuck with a new one. If you make sure that the chuck screw is not there you can remove the chuck with a couple of steps. Make sure the drill is in it's lowest gear. Use a strap wrench or some large vise grips on the chuck. If there is still one jaw in the chuck make sure it is all the way open and locking the collar to the chuck. The chuck will come off in the regular lefty loosey configuration. It may be stubborn. If this is the case, You may have to cut the collar off the chuck and use a pipe wrench. Or bring it to a professional to get it changed out.

Sep 23, 2009 | Makita 18 Volt Cordless Hammer Drill Kit ...

2 Answers

Broken Makita Drill 6408k chuck


separate the housing and remove the gear assembly and chuck ....see if you can use a open end wrench on the shaft and locking pliers on the chuck body

Sep 17, 2009 | Makita 6408K 3/8" Variable Speed,...

1 Answer

Black decker drill keyless chuck won.t open !


hold the back of the chuck with channel locks or a vice and use the same channel locks on the front and open the chuck manually it should work and you can get to the screw to replace it or the hand chuck. this can be a little frustrating but hang in there and you'll be a pro shortly.

Sep 02, 2009 | Makita Usa Inc No.8390DWPE 18V Crdls...

1 Answer

Damaged chuck


Grasp chuck, reverse it until fully open. Look inside where bit goes and should be an allen head or torque head screw holding chuck to motor arbor/shaft.

May 14, 2009 | Makita 5/8" 2 Spd Hammer Drill

2 Answers

Stuck chuck


open the chuck all the way, insde there may be a screw in the bottom it's lefthand thread turn it clockwise to remove, the chuck is also threaded, right hand thread. close the jaws on the short end of an allen wrench and strike the long end with a hammer to break it free

Apr 01, 2009 | Makita Usa Inc No.8390DWPE 18V Crdls...

2 Answers

Makita chuckless drill stuck full open


If you haven't fixed it yet here is the way that I have used to solve this problem. Spray some WD-40 on the inside of the chuck. Place a shop rag around the chuck and CAREFULLY grip with a pair of channel lock pliers set the drill rotation so that it will extend the jaws and SLOWLY depress the trigger. It should move. Let me know if I can help more. When trying this DO NOT SQUEEZE TRIGGER to full RPM.

Sep 11, 2008 | Makita Tools 18V 1/2" Lxt Lithium - Ion...

Not finding what you are looking for?
Drills Logo

Related Topics:

101 people viewed this question

Ask a Question

Usually answered in minutes!

Top Makita Drills Experts

efs_perpends
efs_perpends

Level 3 Expert

1997 Answers

epangan29

Level 2 Expert

113 Answers

Mike

Level 3 Expert

4369 Answers

Are you a Makita Drill Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...