Question about Haier 11000 Btu Portable Ac Air Conditioner Cpf11xcl-ew

1 Answer

My CPF11XCL-EW, when put in COOL mode will short cycle once or twice and then the display turns off. Anyone know what the problem is?

I have it running on it's own circuit. The airflow is not restricted. The water tank is empty. I bought it used and previous owner said it kept blowing her circuit but they just moved to an older house with old wiring and not on a HOME RUN circuit.

Posted by Anonymous on


1 Answer

Kyle DeLory

  • Level 1:

    An expert who has achieved level 1.


    An expert that gotĀ 5 achievements.

    New Friend:

    An expert that has 1 follower.


    An expert that hasĀ over 10 points.

  • Contributor
  • 18 Answers

There could be multiple thing that could cause this if you are lucky it is in the electronics of the unit but with these portable room air conditioners just like the old window units the tend to get refrigerant leaks easily due to the constant moving around and they do not come with service ports so it could be a low pressure safety switch shutting the unit down find the wiring diagram either on the unit in the owners manual or online if you don't understand it see if you can find someone local that does to test the electrical components if all are good then unfortunately it would be cheaper to purchase a new unit than to have this one serviced

Posted on May 28, 2016

  • Anonymous May 31, 2016

    Sorry, meant to click helpful, wouldn't let me change it



Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

How do I turn off the cooling option on my Novamatic microwave?

The word COOL is displayed when the microwave goes into a cooling cycle. The cool cycle is a feature that ensures the operating components of the microwave (Inverter and Magnetron) are cooled after operation by running the fan inside the microwave.
The cooling function is activated whenever the microwave runs for over 3 minutes or is operated twice within a 10 minute period. The word COOL is displayed to tell you why the fan is still running. You do not have to wait for the cool cycle to complete before using the microwave again, simply enter the cooking operation you wish to perform and the cool cycle will stop and the microwave will perform the cooking operation you have just entered.

May 10, 2018 | Microwave Ovens

1 Answer

Does anyone know the Comcast Remote code for NEC LCD-4020-2-av?

Try the following code for your TV.

0030, 0056, 0497

1.Turn on the TV.

2.On the remote control, press a device key once ( TV).

3. Press and hold Setup until the selected mode key blinks twice, then release Setup.

4. enter any one of the code listed. If you perform this procedure correctly, the selected mode key will blink twice.

5. Aim the remote control at your device and press Power once.The device should turn off. If it does not respond, repeat steps 2 to 6, trying each code listed


Feb 20, 2011 | NEC MultiSync LCD40202AV 40 in. LCD TV

1 Answer

Texas Instruments BA-ll Executive Business analyst. How do I put it back into financial mode?

Turn calculator ON. Press the MODE once or twice. As you do so look at the screen. When Mode is in Financial, the screens displays a small Fin.

Feb 11, 2011 | Texas Instruments BA-II Plus Calculator

1 Answer

The Panasonic SC-PT673 Home theater amplifier is not turning on. Pressing the Power or Open/close buttons will produce two clicks from an internal surface mount relay. No display. No sound. Fuse inside...

Generally speaking, an amp protects itself from heat, shorts and overloads by refusing to turn on or stay on.

Overloads can be from excessive periods of high output and shorts would be wiring issues or a speaker blowing up.

You should be able to feel if it's hot. WHY is it overheating? Make sure it has sufficient ventilation on all sides and that vent holes are not blocked by dust balls. Ensure the fan (if equipped) is running as designed (some only operate on demand). Clean dust and debris from it.

If the amp comes back on after cooling, you're lucky. They only have so many self-protection cycles in their lives so continuously resetting or cycling their power without addressing the cause can do more harm than good.

If it protects immediately on a cool power up you should disconnect the speaker connections and try it 'naked'. If it comes up then diagnose which lead(s) are shorted. If it does not come up the problem is internal and should be left to an experienced hands-on tech.

Feb 06, 2011 | Panasonic SCPT673 Theater System

1 Answer

I have a Braemar LCB450-G evaporative cooler. There are two Diagnostic LED,s on the electrinics module,one red & one green. When the power is turned on at the module the red LED remains on & the...

There are several possibilities, the drain valve is opening and closing, this causes water to fill the base, the float valve will not achieve the desired level so the fan will not start. This could be the drain valve actuator is U/S or the PC board. Have you tried to turn the main power off at the switch board for 1/2 hour?
Most occasions the service person will swap out all the units as they purchase it as a package. It is not cheap to replace these units.

Nov 22, 2010 | Heating & Cooling

1 Answer

How do u turn off the alarm on a baby g shock. Like how do u turn it off forever?

mcdevito75 Here, You should be able to reach the alarm thru the MODE cycle, Press MODE and see Flashing display, press Mode for each function till you reach alarm and put alarm to off, if you have t1 and t2 time you"ll have to do this twice.

Oct 26, 2010 | Casio BG191 1B2 Baby G Watch

1 Answer

I cannot figure out how to advance a cycle without having to go through the entire cycle. For example, I had a drain problem with my sink and the plumber put the rinse and hold cycle on for about 10...


Welcome to FixYa.

Your post doesn`t specify a model number, however on most Bosch dishwashers in order to change from "rinse & hold" to "regular" ( or any cycle ) simply turn the unit "on" and once the machine begins push the regular button twice.

Or the button applicable to the cycle you want.

That should change the display to look like this...

If this doesn`t work, try it for "econo" or any alternative and let me know how it goes.

Good luck.


Macmarkus :)

Sep 03, 2010 | Bosch Dishwashers

1 Answer

Can't figure out how to print test page when not connected to PC

Please follow the steps given below to perform a Self test:

1. Turn off the power by pressing the Power button once.

2. Press and hold both the Start button and the Power button.

3. Once the screen displays Mfg Menu enabled, release both buttons.

4. Press the Mode button three times. All the indicator lights will go out and the screen will display LCD button test.

5. Press the up arrow (Up arrow button) twice. The screen will display Single Test Page.

6. Press the Start button once. The self test will begin. The printer will stop once the page has printed in full.

7. Turn the printer off and then back on to disable the manufacturer menu (Mfg Menu).

Apr 05, 2009 | Lexmark X3480 All-In-One Printer

1 Answer

"cooling" display won't turn off causing heating problems.

Try cleaning off the two curved metal bars (about 4 inches long) on the inside near the lint filter. They are what senses the moisture on automatic dry. When you use fabric softener sheets, the stuff from the fabric softener sheets can coat the bars, which makes the dryer think the clothes are already dry, and puts the dryer into cool down. (using time dry will also take the moisture sensor out of the cycle, if you'd like) This should be a Fix-Ya for your problem.

Dec 15, 2008 | Dryers

Not finding what you are looking for?
Haier 11000 Btu Portable Ac Air Conditioner Cpf11xcl-ew Logo

64 people viewed this question

Ask a Question

Usually answered in minutes!

Top Haier Heating & Cooling Experts

Tom Chichester

Level 3 Expert

55954 Answers

Zoom-The Computer...
Zoom-The Computer...

Level 3 Expert

2000 Answers

Thomas Woodburn
Thomas Woodburn

Level 3 Expert

2410 Answers

Are you a Haier Heating and Cooling Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides