E2 N WATER LEAKING

The E2 error code on an LG washing machine usually indicates a problem with the water supply. Here are some steps you can try to resolve the issue:

1. Check the water supply: Make sure that the water supply to the washing machine is turned on and the water pressure is adequate. If there is a problem with the water supply, fix it and try running the machine again.
2. Check the water inlet valve: The water inlet valve is responsible for controlling the water flow into the washing machine. If the valve is faulty, it can cause the E2 error code. To check the valve, unplug the machine and turn off the water supply. Remove the hoses from the valve and check if there is any debris or damage. If the valve is damaged, it will need to be replaced.
3. Check the water level sensor: The water level sensor is responsible for detecting the water level in the washing machine. If it is faulty, it can cause the E2 error code. To check the sensor, unplug the machine and locate the water level sensor. Check for any damage or debris and clean it. If the sensor is damaged, it will need to be replaced.

If the above steps do not resolve the issue, you may need to contact a professional for further assistance.

Strange that it's orange.
Strange that it's freezing in a fridge.

It sounds like the defrost drain is blocked? Does it do this once every 24 hours? You clean it up and next morning it is wet again?

Google

make model clear defrost drain

'make model (what is is)' in all questions please.

Generic help videos here

https://www.google.com/search?q=%E2%80%8Bmake+model+clear+defrost+drain

..

I guess you got a Korean washing machine
Daewoo right ?

E2 shows on display with 2 tone sound and when press power button E9 code appears and doesn't work .
If you confirm this then it's simple 5 minutes work fix.

The pressure sensor is defect or were valve aways leaking water.
Unplug power
Unscrew 2 screws from top cover and slide it back to remove
First thing keep water hose connected and water supplied open detergent drawer and take a look and see if water is comming inside when unit is unpluged from power .If no water leaking them next step is pressure e sensor
You 'll see it a brown round shape with a hose attached to it unplug the 3 colored wires pink red and white all in single connector .
Unscrew and replace it also another thing to check
Is blow by your mouth some air in pressure sendor hose to check if it's cleared you should get a little bubble noise due to water residual in tub it's normal thing and final thing Open drain pump filter to check if it's blocked that's it .
If you are an electrical person please reply to give you more technical information about testing the pressure sensor and electtonic board before buying new one
Regards .

SMEG DISHWASHER ERROR CODE E2? - How To Mend It

howtomendit.com > Kitchen Appliances, Electric Kettles
Free repair help - smeg dishwasher error code e2. ... Q & As - mend, repair, fix kitchen appliances, electric kettles, kettles, water, not, plug ... Search for - error, e2 ...

An E2 code is often an indicator of an electrical problem inside the water heater. The most common problem is with the inlet water temperature sensor. Often a reset will fix the problem. To achieve the reset unplug the unit. Open the unit being careful of fragile electrical wires. Next remove the computer board and then disconnect each plug in wire and reseat them one at a time. Reassemble the unit and plug it in. It should be in working condition, without the E2 code.

water tank is full of water. empty the inbuilt water tank so say that post, good luck!
have Digilex air con and it is showing E2 what is it

Message = E2
Error = OVERFLOW ERROR
Cause & Solution =
The water is supplied continuously due to an defective inlet valve. Change the valve inlet.
The valve inlet is normal, but the water level sensor Change the water level sensor
(sensor pressure) is low. (sensor pressure).
The drain motor does not work - Test and if faulty change the drain pump


Message = E9
Error = SENSOR PRESSURE ERROR
Cause & Solution = The water level sensor is faulty. Change the water level sensor. (remove pressure tube and blow through it to make sure it is clear first)

According to the Ford Audio Manual ERROR E2 is "Over temperature error"....meaning that the unit is getting too hot.

Check the air vents and make sure your car heater is not leaking hot air into the CD unit