Question about Bosch SHE4AP06UC Dishwasher

1 Answer

How can I reset our dishwasher

Tried to reset our dishwasher. It says it is clean but has not run a complete cycle.

Posted by Burton Beebe on

Ad

1 Answer

jroscar1027

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

    Corporal:

    An expert that hasĀ over 10 points.

    Welcome Back:

    Visited the website for 2 consecutive days.

  • Contributor
  • 19 Answers

Open the dishwasher door sufficiently to see the control buttons, then hold the two buttons with labels "Cancel Drain" and press for 3 seconds.
Close the door. Wait nearly 1 minute for the dishwasher to complete the cycle.
Open the door and hold the "ON/OFF" toggle.

Reset Bosch Ascenta Dishwashers
Shut off the child lock if needed by pressing and holding "Open the door far enough to see the keys, then hold the "START RESET" toggle until the "ACTIVE" LED become extinguished. On the SHE5AM model of Bosch Dishwashers, hold the "START RESET" key until the display clock shows "0:01".
Close the door and rest about 60 seconds. On the SHE5AM, wait until the display clock displays "0:00".
Open the door and hold the "ON/OFF" toggle.

Posted on Apr 06, 2016

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Kenmore Dishwasher model 630.1390 is starting it's cycle but then indicating it's complete less than 3 minutes later. Occasionally it runs through to completion, but usually not.


sounds like the timer is bad, or intermittent, might be cheaper depending on age to replace the whole thing. parts ( esp timers which are main points of a dishwasher are costly.)

Apr 28, 2015 | Kenmore Dishwashers

1 Answer

How to reset Blomberg DWT23100W computer?


Remove lower dish basket and inspect where water drains looking for clogged inlet

Jun 02, 2014 | Dishwashers

1 Answer

Whirlpool Gold dishwasher not cleaning dishes. It runs through the cycles and rinses, but dishes are not completely clean.


I had a similar problem with my last two dishwashers, with food still left on the dishes at the end of the cycle. What a nightmare. The most recent dishwasher is new, now the problem is solved. Here's what the manufacturer told me. Pour white vinegar (approximately 2 cups) into the dishwasher and run through the cycle. Buy some Cascade Complete and only use this type of soap for the dishwasher. Make sure you run a cup or two of the white vinegar through the dishwasher cycle once a week. My dishes are now clean and clear!!

May 26, 2011 | Whirlpool Dishwashers

1 Answer

There is a smell in the dishwasher and on the dishes when clean


I suspect stagnant water is laying in the bottom areas. You will have to lay the machine on it's back to access the pump.

May 27, 2010 | KitchenAid KUDK03ITBK Built-in Dishwasher

2 Answers

How do you reset the whirlpool gu2400 xtp83 dishwasher. the clean light is flashing. The unit will not start


Can be caused by detection of a heater circuit problem. You can reset by running the diagnostic cycle. To turn of the diagnostic cycle, press: HEATED DRY button, then NORMAL button, HEATED DRY button again, then NORMAL button. The cycle runsfor ~22 mins. When it completes, the blinking light should go out. You can then try running the dishwasher again. If the problem comes back, the heater element or Thermister may need to be replaced

Jul 29, 2009 | Whirlpool GU2455XTS Built-in Dishwasher

1 Answer

Light flashing


reset the dishwasher by touching heated dry and normal let it run through that cycle then through a normal cycle got the error blink again. Reset dishwasher by touching heated dry and normal, ran the test cycle, next ran a normal cycle but turned off the heated dry. This allowed the dishwasher to run through a complete cycle did not get the error blink and confirmed that the heating element was out.

Aug 30, 2008 | Whirlpool 24 in. GU2500 XTP Built-in...

2 Answers

Kenmore Ultra Wash Dishwasher LIghts are blinking....


I just read this for the same problem: push sanitize, then heat and dry, sanitize, heat and dry, sanitize, heat and dry, cancel, then open and close the door. It worked. The dishwasher is running correctly even as I type this. 

Feb 11, 2008 | Kenmore 24 in. 17262 Built-in Dishwasher

Not finding what you are looking for?
Bosch SHE4AP06UC Dishwasher Logo

1,406 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bosch Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Mike

Level 3 Expert

4372 Answers

Are you a Bosch Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...