Question about Maytag Neptune MAH5500B Front Load Washer

Open Question

NF CODE, BUT FILLS WITH WATER, BUT DOES NOT SPIN.

Washer fills, washes, then 15 mins left, has to spin, I get the nf code and it stops?? please help!!!!

Posted by TERESA ELEFSON on

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: Help!! My maytag neptune MAH6700AWW is having trouble.

the fix was simple i just had to lift my drain hose off the floor. it had become disconnected from the back of the washer and was lying on the floor. I didn't realize that by it lying on the floor it didn't provide the proper back pressure to keep the water in while filling the tub. this was the NF error. as for the LE error. i haven't gotten it since i took off my cold water hose connection and ran hot water into it to losen the dirt/rust that was caked into the screen that is located in it. My washer is running like it is brand new again.

Posted on Feb 20, 2008

Ad

Anonymous

  • 22 Answers

SOURCE: fills with water but wont wash or spin

The code LR stands for locked rotor you will need a new motor and motor control kit pretty expensive and only covered under you warrenty for a year!

Posted on Aug 17, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: getting nf code on final spin cycle

The "nf" code is a "no-fill" fault. This indicates that your washing is not getting water supplied to it, or the pressure isn't substantial enough to complete a fill. You need to, first, make sure the water supply is turned on. Second, if the water IS turned on, and you're still not getting anything to your washer, you may have a fill valve problem. The fill valve is what both your hoses connect to on the back of the machine. It can become clogged with sediment over time (especially, if you have hard water or well water). Turn the water supply off and remove both hoses from the back of the washer. Check both these hose connections for clogs in the filter screens. If they are clear, then more than likely the fill valve has gone bad. I hope this helps you. 

Posted on Dec 13, 2008

Lanijo58

Lani Tuggle

  • 73 Answers

SOURCE: when i am on spin cycle it stops and has a nf

This error code, pops up usually when in the spin cycle, your clothes are out of balance, too heavy of a load, or even at times it can happen with a too light of a load. Just stop or pause your washer and re arranged the items inside,

Posted on Jul 08, 2009

richroth

Richard Roth

  • 9472 Answers

SOURCE: nF code comes up and washer has just finished its

The "nf" code is a "no-fill" fault. This indicates that your washing is not getting water supplied to it, or the pressure isn't substantial enough to complete a fill. You need to, first, make sure the water supply is turned on. Second, if the water IS turned on, and you're still not getting anything to your washer, you may have a fill valve problem. The fill valve is what both your hoses connect to on the back of the machine. It can become clogged with sediment over time (especially, if you have hard water or well water). Turn the water supply off and remove both hoses from the back of the washer. Check both these hose connections for clogs in the filter screens. If they are clear, then more than likely the fill valve has gone bad.

Posted on Jan 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

MAYTAG NEPTUNE WITH NF SYMBOL


Symbol - 'Washer has tried to fill' Check water faucets & hoses for kinks. OR call Maytag 1-800-688-9900. Happy Washing!!!!

Nov 02, 2016 | Maytag Washing Machines

1 Answer

Nf code and donnot continue to next cycle


Samsung Washer Error Code NF (Fixed ...

www.appliancerepairlesson.com/.../samsung-washer-error-code-nf-fixed/
Jan 11, 2014 - What does the error code NF mean on a Samsung washer? ... You can set the washer to any cycle and test each solenoid for proper voltage. ... Next would be to check the screens on the back where the water hoses connect. ..... Hi, you don'thave any power to the water valve wires when it should be filling?

Dec 15, 2015 | Frigidaire Affinity ATF7000E Front Load...

2 Answers

HOW TO FIX NF CODE IN MAYTAG WASHING MACHINE


Hello & Welcome to FixYa

NF error in your Maytag is displayed due to no fill condition, when the washer tries to fill but is unable to nf is displayed. Please check the water inlet valve for any clogs and obstructions, you can also clean the inlet to solve the issue. Please get back to me if you have any other questions.

Kevin

Oct 02, 2011 | Maytag Neptune MAH5500B Front Load Washer

2 Answers

The code nf keeps coming up what does that stand for


NF(No Fill) code indicates that the washer is not getting enough water supply. Check if wwater supply is turned On and water is coming through the pipe. Then the fill valave can be clogged. t can become clogged with sediment over time
Stop the water supply and then remove the hose and then check for any clogs and if they are fine then in your case most probably your fill valve must have gone bad for this problem.Replacing it must solve the issue.

Jan 14, 2011 | Samsung WF337AA Front Load Washer

1 Answer

My Maytag Neptune will not go into the spin cycle, instead the letters "nf " come on the display. What can I do to prevent this and to have the cycle completed?


Bonnie,

NF = No Fill the control board receives signaling for the washer during the water fill cycle. With most cycles the depth of water is around 3.5 inches in the wash basket. I know a Bulky Wash cycle selection will fill the wash tub to a high fill which is about 7.5 inches of water in the wash basket.

Is the washer filling the machine with any water? Do you hear water entering the machine? If you are doing a cold water fill and there is no or very little water in the wash basket with the NF error code. Try a Warm or Hot fill and see if the machine will fill and start the wash cycle.

Assuming you are doing cold water wash loads. You could have a water line block at the inlet screen or a failed cold water inlet valve which will not open. Try the above and let me know the results..........Rich

Sep 13, 2010 | Maytag Neptune FAV6800AW Top Load Washer

2 Answers

My Maytag Neptune will not spins and gives the code nf. I have been told that there is a reset code. Does anyone know the code?


Hi


Thanks for using FixYa. Error NF means No Fill. The washer has tried to fill but was unsuccessful. NF indicates No Flow. There is something that is interrupting the inbound flow of water to the washer, either hot or cold. Sometimes this happens when water service in the area is interrupted, creating an air pocket that causing the water valve not to sense water.

Try running the diagnostic test by—
  • Press the delicates and heavy soil keys together for 3 seconds.
  • You are in the service mode.
  • Now, press wrinkle free key, cold water should start entering.
  • Then, press the cotton sturdy and hot water should flow.
  • To exit the test mode, either unplug the machine or press the delicate and heavy soil again for 3 seconds.
Please do rate the solution if the issue is resolved or post a comment for further assistance.


Thanks
Rylee

Aug 22, 2010 | Maytag Neptune MAH5500B Front Load Washer

1 Answer

Code nf shows on my washer


unplug for 15 mins and plug again to rest

Sep 14, 2009 | Whirlpool Calypso GVW9959K Top Load Washer

1 Answer

Maytag neptune TL


The machine needs to cut you a break;

“”i have a maytag neptune TL and there are several things wrong with it...1. I can't wash small loads it will stop at the spin cycle and flash dc””

This issue is a clutch issue see this post to DIY the repair.

“”it will wash fine on regular loads until it comes to spin cycle again and it will stop and flash nf””

This one is a little confusing the “nf” error is a No water fill error code. Check these two post for support regarding water inlet restriction or valve not opening properly.

nf post nf post 2

“”my fabric softener dispenser will not let the softener out neither will the bleach dispenser””

See this fabric softer post for support. The fabric softener dispenser may be clogged or the water dispenser valves feeding both dispensers may not be operating properly. The Service Manual on page 16 “Board Output Test” will give you support to turn on the Fabric Softener Valve and Bleach valve. See if you hear the valves operate in Service Mode”

My method may seem a little confusion for viewing water flow to the dispensers. This issue could be associated to the nf error you are receiving, restricted water flow (inlet screen clog) or cold water valve not working properly.

Post back for any questions or possible support I can offer. I’m an owner like you not a repair person but I’m very comfortable working on this machine. Rich

Jun 17, 2009 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Getting nf code on final spin cycle


The "nf" code is a "no-fill" fault. This indicates that your washing is not getting water supplied to it, or the pressure isn't substantial enough to complete a fill. You need to, first, make sure the water supply is turned on. Second, if the water IS turned on, and you're still not getting anything to your washer, you may have a fill valve problem. The fill valve is what both your hoses connect to on the back of the machine. It can become clogged with sediment over time (especially, if you have hard water or well water). Turn the water supply off and remove both hoses from the back of the washer. Check both these hose connections for clogs in the filter screens. If they are clear, then more than likely the fill valve has gone bad. I hope this helps you. 

Dec 11, 2008 | Maytag Neptune MAH5500B Front Load Washer

Not finding what you are looking for?
Maytag Neptune MAH5500B Front Load Washer Logo

Related Topics:

1,014 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Washing Machines Experts

Bill Long

Level 3 Expert

606 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Brad Brown

Level 3 Expert

18204 Answers

Are you a Maytag Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...