Question about Whirlpool Dishwashers

1 Answer

Whirlpool quiet partner ii clean light flashing 7 times. I installed a new heating element and reset the code, and it still flashes 7 times

Posted by Chris McDowell on

Ad

1 Answer

Gere knutson

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Whirlpool Master
  • 842 Answers

Hi,

Check the main control for the heater relay, this may be faulty and the cause of your issue. Good Luck

I’m happy to help further over the phone at https://www.6ya.com/expert/gere_bf68e6055dd61249

Posted on Apr 02, 2016

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Does my whirlpol du1145xtpb1 dishwasherr need to be reset


SERVICE DIAGNOSTICS CYCLE
To start the Service Diagnostics Cycle, press the
following keys, in order, in less than 6 seconds, while in standby(power on but unit off):
Heated Dry, Normal, Heated Dry, Normal
To Rapid advance one interval at a time, press the Start key, noting that
unlike Standard cycles, the Diagnostics Cycle automatically resumes
after door openings and does not require pressing Start to resume.

Once the diagnostic cycle has run and shut off, run a normal wash cycle, empty and with no detergent, to reset the control to factory "normal" operation. Make sure there's plenty of hot water.


Read more: http://forum.appliancepartspros.com/dishwasher-repair/261055-whirlpool-quiet-partner-ii-clean-light-flashing-have-reset-still-flashing.html#ixzz2UOcsE2Yg
http://forum.appliancepartspros.com

May 25, 2013 | Whirlpool 24 in. GU3200XTP Built-in...

1 Answer

I have a whirlpool quiet partner II dishwasher model # DU1055XTVB5 and the normal light is steady flashing I have did the sequence to reset HEATED DRY NORMAL HEATED DRY NORMAL and the normal light...


Angelia:
Thank you for your review.
We would like to inquire further about your review with you. Please respond back to this email address, [email protected], with your name, phone number, street address, zip code, model & serial number, and date of purchase on the appliance.
We look forward to your reply.
Thank you,
Whirlpool® Social Media Relations

Mar 06, 2018 | Whirlpool 24 in. DU1055XTP Built-in...

2 Answers

Whirlpool Quiet Partner II clean light blinks 7 times


The clean light flashing 7 times is an error code indicating an issue with the wash temperature. If the control does not detect a 4*F temperature rise in the main wash cycle, it will display the fault as the clean light flashing 7 times. There are several things that could cause the water not to heat, including the water being too hot coming in, an open door switch, or a faulty component in the heater circuit. The most common cause is the door switch not closing properly. This can be due to a loading issue or a latch issue. If upon visual inspection of the heating element no obvious defects are found, I would recommend resetting the control and running another cycle, paying close attention to door closure. If the light begins flashing again, you likely have a component failure. The heat circuit consists of several components including the element, control, door switch and tub thermostat(s). Reset the control by pressing teh following buttons within 5 seconds.

Hit Temp Wash Heated Dry Hi Temp Wash Heated Dry
.

Mar 02, 2012 | Whirlpool Dishwashers

1 Answer

Whirlpool Quiet Partner V light flashing


most of the time this meens your heat element is burnt out.

If you need further help, I’m available over the phone at https://www.6ya.com/expert/dude_653d05454b389bba

Feb 25, 2010 | Whirlpool Gold 24 in. Built-In Dishwasher...

1 Answer

Whirlpool quiet partner III. Clean light keeps flashing clean.


Had the same problem. Press the sani-rinse and heated dry button back and forth and it should reset.

Aug 29, 2009 | KitchenAid 24 in. KUDI02IR Built-in...

1 Answer

Clean light flashing Quiet Partner V


do the heated dry and hi temp and then hitr cancel. you know what this means?! you have a bad heating element usually. call for service this should be a covered repair if it is only 6 months old

Mar 26, 2009 | Whirlpool GU2400XTP Built-in Dishwasher

1 Answer

Whirlpool Quiet Partner 980


Bad control board ,replace it.

May 26, 2008 | Dishwashers

Not finding what you are looking for?
Dishwashers Logo

Related Topics:

196 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Dishwashers Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Mike

Level 3 Expert

4372 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Whirlpool Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...