Don't have instructions for machine just push start?

First, If you are not familiar or comfortable with opening your laptop DON"T DO IT. There are tutorials , Videos, instructions, online to follow. More harm that good can result. That said, I appears ypu machine is looking for a boot disk or boot media, unplug the machine,I don't know the make, model, OS, remove the battery, leave it out, plug the machine in , push on/off button, try to start normally. If that fails, unplug,plug in AC, push the on/off buttom, start tapping IMMEDIATLY the key" esc", F-1, F-2, and so on to F12 in Quickly one after another moving left to right, We are trying to get a response from the machine, If you see a pre-boot page with esc-setup or F-1 or F-whatever tap that key fast. I see from the very short vid it says "PRESS ANY KEY" Did you press any key??? when that page poped up? What happened? Your machines MBR seems to be missing. Respond to this post for further assistance.

push stop button for a few seconds until it beeps or the readout changes. unplug,,,,,plug back in....push "Select" or "menu" button depending on which machine you have....push again and again until the program you want is on the display or readout. Then push the "start" button ....Don't push any timer buttons or arrows!

Hi
If you push the scoop but don't put any coffee in the brew group, what happens? If it brews right (water comes out), then I would suspect that your coffee is too fine. Push the lever below the grinder on the right to the back (#7) and then try to brew again. Don't let it go all the way. Push the coffee button as soon as it starts to brew. Do this 3 times. The 4th time let it go and see if it will brew. If it doesn't I would need more information.

go to www.directed.com this is the manufacturer of the viper remote starters, there you should be able to download instructions.

Here is how you program the viper 5101 remote.

Programming the Viper Remote Starter 5101

Unlock the doors before starting

Push and hold f button for 8-10 seconds until amber light is on solid

Push Remote start button for about 4 seconds till amber light flashes 3 times

Put key in IGN to the on position but don

Is this a NEW appliance? BE SURE TO READ THE INSTRUCTION MANUAL OR QUICK START.
If this is a used machine, perhaps there's something wrong that you need to check out. BUT......
Pushing-in the Timer wheel is sometimes necessary on the older machines--it's the round wheel with the wash/rinse/spin cycles imprinted on the panel, a "wheel" which turns to the various cycles as the machine operates. Many of them pull-out or push-in to operate the machine. Find the appropriate cycle and rotate the wheel to the corresponding location, then PUSH-IN. The washer should respond.
If there is a problem with the water supply entering the machine or other hazard the machine will shut off until it is repaired.

To automatically descale your machine, press the scoop button and hold it down until you enter the menu. Use the arrows on the left to scroll down until you come to "direct water connection" and push the enter. Chose "off" and push enter. Push "escape". Use the arrows on the left to scroll down until you come to "Descale". Press enter and the machine will enter the mode to descale your machine. The process takes about 45 minutes. You don’t have to do a thing except mix a full water tank with descaling solution and have a container under the steam wand when your start. If you have a cappuccinonatori on your machine you will need two containers. To start the descaling process, simply turn the steam knob. When the process is over your machine will say "Descale finished". Remove your water tank and rinse it out. Refill it with fresh water. Replace on the machine and start the descaling process over again to rinse your machine. Go back into your menu and scroll up or down 1 to signal descale and enter. Choose "Yes" and push enter so the machine will tell you when you need to descale again

Water tab goes off all the time, get rid of machine, don't buy Bosch

Thats called the primer Make sure the on/off switch is on the on,Push the primer at least 4 to 5 times,then pull it..once it starts you may have to push the primer a few more times to keep it running once it runs on its own and you dont have to push the primer to keep it running Cut Away,Also one more thing you probably already Know make sure its full of bar oil..Hope this helps you and have a great day...

I’m happy to assist further over the phone at https://www.6ya.com/expert/joe_a3369546f8067589

The Company Idea Village of the Handy Stitch are sending me the instruction manual.

The two parts are each shaped like L's. While holding the release button, pull the two parts away from each other.