Question about Crosley Washing Machines

1 Answer

Washer will not come on, I have checked the power supply and its good. Is there a way to reset electronics besides unplugging?

Model CAW9244BW0

Posted by Matt Sharpe on

Ad

1 Answer

Melissa Martin

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Crosley Master
  • 753 Answers

Are you saying that the lights are no coming on and there is no action at all? If you have no power at all you will no be able to perform diagnostics. You can look and see if the control board is receiving power by checking the L.E.D. light on the board. To access the board you will remove the screws going across the back of the console and then with a putty knife depress the clip on either end of the console from the front and tip it toward you. Please be super careful because there is electricity in this area. We don't want you to be come damaged with servicing your machine. If you need further assistant I am here to help.

Posted on Feb 06, 2016

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Is there a reset button or someway to get the washer back on besides having to wait for it to come back


on some models the motor reset is done by unplugging it for a couple minutes then plug it back in, on others u can open and close the lid slightly not fully 6 times within a 12 second period and it will reset the motor. on others u have to push start, cancel or some other buttons, to reset appliance. u can check the manual or youtube on how to do ur specific model

Jan 15, 2015 | Washing Machines

1 Answer

It displays 'control lock' with red light


Here are a few Different models as i do not know yours.
How to Unlock the Control on Whirlpool Duet eHow

Maytag - To unlock the controls, press and hold the CYCLE END SIGNAL for 3 deliberate seconds or until the control lock light goes out. If the control locked light will not turn off, I recommend unplugging the washer for 5 minutes. Plug the unit back in and see if the controls will respond. If not, I recommend calling a service technician to diagnose and repair the washer. You could have a failed control console or a bad electronic control board in the washer.

Kemmore- Unplug for 10 minutes.

GE washer - Make sure that the control for the washer is not locked. If it is, press and hold the LOCK button for 3 deliberate seconds (or until the control unlocks).

There is not another way to reset the control board other than completely unplugging the washer as you have been doing. Since the display light up and works, the washer apparently has electrical power supplied to the control board and control console. You could have a failure in the console that is preventing the start button from working. A failed control board or a problem with the door switch could also prevent the washer from starting. Make sure that the washer door is firmly closed.

If the washer will not start after checking the control lock and the door, I recommend calling a service technician to diagnose and repair the washer.
Good luck More info would be helpful. Make and model. Is always a plus.

Oct 02, 2014 | Washing Machines

1 Answer

My Maytag washer will not complete a cycle. The code Lr is display on the front of the washer. I have pulled the plug and reset the breaker.


Hi.

LR stands for locked rotor. The code is returned by the Motor Control Unit (an electronic module connected to the motor and to central control unit). The code is returned when no motion from motor rotor is detected. With many models LR may be due to a factory defect. Please call Maytag and check if any recall has been issued for error LR concerning your washer model. If recall has been issued you will get a kit comprising a new motor and wiring harness.

You can also try temporarily resetting the error by disconnecting power at circuit breaker (or unplugging power cord). If the error message is prompted again call Maytag.

Regards.

Ginko

Aug 08, 2011 | Maytag Washing Machines

1 Answer

Hello, Re: frontloading washer Model C45172 Our washer has been operating withiout hitch since purchase about five years ago, We love it. Today I tried to program it to do an extra rinse after wash...


For the Elite (HE) machines:

Press 'STOP' twice, press 'POWER', choose a wash cycle (such as 'NORMAL'), select wash options (water temp), press 'START' to finish the reset sequence.

Other Kemore electronic washers:

Unplug the machine for a minute, plug it in. Press 'PAUSE/CANCEL' twice.

Good luck from Detroit, MI.

Jun 12, 2011 | Kenmore Washing Machines

1 Answer

I have a Kenmore model 11049962603 that displayed an f-71 error code. I ordered a new cpu computer from sears and installed it. the machine seemed to work for one or two loads. now it displays an f-70...


I provided a complete list of error codes for this type of washer in the image below. The error codes vary by the exact model of HE3t washer that you have. Since you have an HE3t that is displaying the F70 and F71 codes, the list below should apply to your model. These are not listed in the owner's manual because they are intended for technicians. Use extreme caution if you follow any of the troubleshooting described in this information sheet. Unplug the washer and shut off the water supply before accessing internal components.

The F70 and F71 codes indicate that you have a communication error between the CCU (Central Control Unit or main machine control board) and the user interface touch pad assembly. Here are some troubleshooting tips:

Make sure that you have the washer plugged into a properly grounded 3 prong 120 volt AC electrical outlet.

Unplug the washer for 30 seconds to allow the control boards to power down and reset. Plug the washer back in but do not touch the power button (or any other buttons) for 1 full minute. This may reset the control board. Pressing the power button too quickly after reapplying electrical power to the washer can cause the F70 or F71 code since the CCU does not have time to recognize the user interface control.

If the above tip does not help then the most suspect component failure is the MCU (motor control unit -- motor control board at the bottom of the washer beside the drive motor). You can check for this failure by unplugging the washer and then pulling the MI3 connection on the CCU. The wiring diagram below has the MI3 connection highlighted in red. The connection has blue wires. The third image below shows this connection on the control board. The connections are labeled on the control board. Press the tab at the bottom of this plug down and then pull it out. Power up the machine with this connection unplugged and don't touch any buttons for 1 minute. If you then press the power button to turn on the washer and don't get the F70 or F71 code then the MCU at the bottom of the washer will likely need to be replaced to fix this problem. A technician would normally be needed to verify this failure and replace the MCU. The MCU is expensive ($423).

This troubleshooting information is based on a common HE3t model that displays the F70 and F71 codes. If you need more help, submit additional details and the full model number of your HE3t washer.

richroth_125.jpg richroth_126.jpg richroth_127.jpg

Mar 27, 2011 | Kenmore Washing Machines

2 Answers

Hi! We were using the internet and lost our connection. There are no lights on the router. We have also tried unplugging and plugging back in. Do you have any other suggestions? Thanks, Vivian


If you only unplugged the power cord at the router end you can try unplugging at the outlet end. Sometimes the AC adapters have a breaker that resets after being removed from power for a little while. You can also try plugging the adapter into another outlet that you know is working because no lights at all just means the router is not receiving power. If all of that fails you may need to have it repaired or replaced. Good luck

Mar 08, 2011 | D-Link 802.11g Wireless Router WBR-1310...

1 Answer

Will not turn on , lights come on, displays cycle time but does not start.


Hello, this is often the electronic card, or motor relay, but it is often worth unplugging and resetting any component connector plugs and sockets, as they can work loose, and low-level electronics sensors rely on good connections.WITH ALL POWER OFF check all you can see, and reset any you can see(i.e unplug and replug).
Thanks

Jun 12, 2010 | Frigidaire ATF6000ES Front Load Washer

2 Answers

Washer will not spin


Electronic motor needs to be reset. Unplug for 2 minutes, plug back in, open and close lid slowly 7 times to reset computer. Also check to see if belt is not broke, pull up top, remove front cover, just lifts off, check belt.

Feb 23, 2009 | GE WBSR3140DW Top Load Washer

2 Answers

Samsung electronics clothes washer model j845


If you have a face icon lit up the child lock is on, press and hold spin and rinse buttons until it goes off

Apr 26, 2008 | Washing Machines

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

55 people viewed this question

Ask a Question

Usually answered in minutes!

Top Crosley Washing Machines Experts

peter gittos
peter gittos

Level 2 Expert

247 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

jdthefixer

Level 3 Expert

746 Answers

Are you a Crosley Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...