7 asterisks in a row on register tape. - Sharp ER-A320 Cash Register

HellooCheck the carbon conductor tracks of that row. it may have a break anywhere. It is a repairable one, as carbon tracks can be drawn into, with a special type of pen and carbon ink. OK.

To store a number into memory, press SHIFT [STO] and the name of the desired memory register. To recall a number from memory, press RCL and the name of the memory register.

Available memory registers are A, B, C, D, X, Y, and M. Those are on the fourth and fifth rows of the keyboard (the two rows immediately above the 7, 8, 9, DEL, AC row). You don't need to press SHIFT or ALPHA to access these names after the STO or RCL.

Check the mtion sensing magnetic switch thats under the seat rail. It determines if you are rowing and sends a signal to the computer. Make sure all connections are fully seated. You may have loosened a wire when you swapped the batteries.

Hi,
To register your product, simply go to this website here: http://pnregistration.harte-hanks.com/Registration.aspx and scroll down to see the registration form. Kindly fill out the required fileds marked with asterisks (*).

Rating my assistance will greatly be appreciated. Thank you.

Go to your asterisk CLI by typing: asterisk -r -vvvvv and check the messages that comes across. You may find a "NOTICE" stating failed to register and the reason why. My case was an ACL permission, which is the Deny or Permit section of the extensions config. Here is the default, which will allow anyone to register and is not recommended. Deny: 0.0.0.0/0.0.0.0 Permit:0.0.0.0/0.0.0.0

it may want to replace the formatter board, call your HP repair center

Clean the drive 5 times in a row with a non expired cleaning cartridge

Hi !!

How to implement Hlookup function:

• Select your data and sort it in ascending order
• Then type '=HLOOKUP(lookup_value,table_array,row_index_num,range_lookup)'.
  Lookup_value is the value to be found in the first row of the table. Lookup_value can be a value, a reference, or a text string. Table_array is a table of information in which data is looked up. Use a reference to a range or a range name. The values in the first row of table_array can be text, numbers, or logical values. If range_lookup is TRUE, the values in the first row of table_array must be placed in ascending order: ...-2, -1, 0, 1, 2,... , A-Z, FALSE, TRUE; otherwise, HLOOKUP may not give the correct value.
  If range_lookup is FALSE, table_array does not need to be sorted. Uppercase and lowercase text are equivalent. You can put values in ascending order, left to right, by selecting the values and then clicking Sort on the Data menu. Click Options in the sort dialog box, click Sort left to right, and then click OK. Under Sort by, click the row in the list, and then click Ascending.
  Row_index_num is the row number in table_array from which the matching value will be returned. A row_index_num of 1 returns the first row value in table_array, a row_index_num of 2 returns the second row value in table_array, and so on. If row_index_num is less than 1, HLOOKUP returns the #VALUE! error value; if row_index_num is greater than the number of rows on table_array, HLOOKUP returns the #REF! error value.
  Range_lookup is a logical value that specifies whether you want HLOOKUP to find an exact match or an approximate match. If TRUE or omitted, an approximate match is returned. In other words, if an exact match is not found, the next largest value that is less than lookup_value is returned. If FALSE, HLOOKUP will find an exact match. If one is not found, the error value #N/A is returned.
• If HLOOKUP can't find lookup_value, and range_lookup is TRUE, it uses the largest value that is less than lookup_value.
• If lookup_value is smaller than the smallest value in the first row of table_array, HLOOKUP returns the #N/A error value.
• If range_lookup is FALSE and lookup_value is text, you can use the wildcard characters, question mark (?) and asterisk (*), in lookup_value. A question mark matches any single character; an asterisk matches any sequence of characters. If you want to find an actual question mark or asterisk, type a tilde (~) before the character.
• In the example in the Excel training video the sorted data represents the density of water at different temperatures. The left most column gives the temperature in degrees and the top column specifies the 'decimal' degrees
• We looked up the density of water at 5.4 degrees celsius using the Hlookupfunction.

Still have problems, Check this video on the you tube.



Hope this would help,

Thanks,
Anurag Shukla

You most likely moved or damaged the senser under the seat check if the wire is loose or damaged the the senser it in the center of the bottom side of the seat Good luck

The most common cause for this is that when you open the reconcile window, the account chosen is not the same account as where the tranasctions are located. Make sure of the account name you are reconciling. Also, look at the trasnactions in the register. If they have an asterisk next to them, they are indicating that they are tentatively cleared. Click on the asterisk until the box is blank. They should show in the reconcile window then. Some versions of the program would allow you clear the transactions directly in the register by placing the cleared checkmark on them. Some older versions would not accept them once this was done, and you had to completely clear the marks in order to reconcile. Also, be sure of the type of account you are trying o reconcile.
If these answers don't resolve the issue, let me know and we will see what we can do.