Processing data but nothing processing

If you are experiencing issues with your Canon IR3300 printer when trying to print in Xerox print processing mode, but it's working fine in regular print mode, there could be a few possible causes. Here are a few things you can check:

1. Check the printer driver: Make sure that the correct printer driver is installed and that it is compatible with the Xerox print processing software. If the driver is not compatible, the printer may not function properly in Xerox print processing mode.
2. Check the network connection: Make sure that the printer is properly connected to the network and that it can communicate with the Xerox print processing software.
3. Check the print settings: Make sure that the print settings are correctly configured for Xerox print processing mode. This includes the resolution, color mode, paper size, etc.
4. Check the Xerox software: Make sure that the Xerox software is compatible with your computer's operating system and that it is properly installed and configured.
5. Check the firmware: check if your printer's firmware is up to date.
6. Check the paper size and tray: Make sure that the paper size and tray are correctly configured for Xerox print processing mode.

Apparently the battery is Circuit Board mounted and is a backup memory battery.

Li (lithium) battery • The Li battery is mounted on the printed circuit board in the data processing unit "QM-Data". Do not dispose of the data processing unit by burning it. If the data processing unit is thrown into fire, the battery may leak chemicals, burst, or burn violently. Comply with government regulations regarding the disposal method.

and

• This error message indicates that the memory backup battery is low, and that if you continue to use the data processing unit "QM-Data", backup will not be performed. Save the part programs and measured data stored in the internal memory of the data processing unit to the floppy disk or to a personal computer. • Contact your supplier to replace the battery.

It also says changing the battery removes any saved data.

So if you are looking to do it yourself, look for screws to get inside.

https://www.mitutoyo.com/webfoo/wp-content/uploads/QM-DATA200_2222.pdf

..

Try going into Control Panel > Printers and Properties, right-click on your printer icon and go into Printer Preferences for that printer. Make sure both Page Size and Output Size are set for the the same size of what you are printing (Letter, Letter/Legal, Legal/A4,A4, etc). Often, Output size is set to Match Page Size...that was causing the problem for me.

Some would say Input, Processing, Output. The diagram would be an arrow from input to processing, then an arrow from processing to to output. Then an arrow from output to Input in this way of looking at it. You will find more complicated descriptions and diagrams, too.

http://technology.blurtit.com/300718/what-is-data-processing-cycle
The data processing cycle:

It is Sequence of steps performed repeatedly by a computer in the execution of a program. The computer's central processing unit (CPU) continuously works through a loop. It fetches a program instruction from memory. Then the CPU fetches any data it needs. Then it applies the data to the program. It stores the result in memory. Then it fetches another program instruction.
Others include more stages: http://www.enterprisefeatures.com/6-important-stages-in-the-data-processing-cycle/

data collection
data preparation
data input
data processing
data storage
data output

I am having the same issue. Seems to get caught in a loop and never prints file.

blinking green light -> Processing Data The printer is processing or receiving data - > To cancel the current job, press the CANCEL button

If it is solid on, it means the printer is ready to print; no action is required. If it's flashing, it means the printer is processing data and should print soon.

If you are printing from your computer and nothing comes out, with the "Horseshoe" light staying solid, I suggest checking the connection between your computer and the printer, or at least the printer configuration. Most of the time, unplugging, then plugging cables back in does the trick.

Not really sure about Mac, but if this happens on a PC, I would first uninstall the printer (software-wise) then download the latest drivers and install.

There is a job waiting to be processed. Need to check status monitor to see what is waiting. If it is not critical you can cancel the job from that same screen.

Because you have an i model copier it must be setup to print and scan also. Someone might have sent a job that could be processed for one reason or another. Look in the bottom right side of touch screen for status monitor and see what details it has.

Hope this helps
TankMurdock

From the OKI site, I found this information. My problem is a Flash 2 Blink, which is a problem with the cover or minor error, whatever that means. I can't figure out how to fix it. Any suggestions greatly appreciated!

Flash type Ready LED (Green) Manual feed LED (Amber) Error LED (Amber) Meaning Flash 1 -- slow blink X The printer is processing data when printing has been suspended. X The image drum required changing or toner is low. Flash 2 -- blink X The printer is receiving and processing data during printing or the printer is resetting itself. X The printer is requesting manual paper feed. X There is a printing error, problem with paper or a cover open. X X X There is a minor error with the printer. Flash 3 -- rapid blink X X X There is a major error with the printer.