Maytag MER6772 Gemini Electric Kitchen Range Logo

Related Topics:

Question about Maytag MER6772 Gemini Electric Kitchen Range

Open Question

Why is bottom oven very slow to heat up?

Replaced element

Posted by Jim Shoemakeer on

Ad

5 Related Answers

Anonymous

  • 878 Answers

SOURCE: bottom oven element on Model MER5552BAW

magic, start with the basics first. See if you have the right power going to the oven. At the terminal block on the oven, where the cord attaches, you should have 120V from the center terminal to each end terminal. You should have 240V across the 2 end terminals. If you don't have this, there is your problem. If that's ok, check the voltage at the bake element terminals in back. Should be 240V when in bake. If that checks ok, then it would be the element itself. Check it, with power off and wires disconnected from the element it will ohm at approx. 20 to 22.6 ohms. If you don't have the power at the element then I would suspect the oven controller. The fact that it's heating to 170 degrees leads me to believe that you are missing a leg of power. Catriver.

Posted on Jun 13, 2008

Ad

Anonymous

  • 1 Answer

SOURCE: Maytag Gemini Double Oven-bottom temp problem

after power outage clock on oven will not set unless the oven itaelf is on unable to set clock

Posted on Jan 28, 2009

Ad

Anonymous

  • 998 Answers

SOURCE: lower element of top oven does not heat on Maytag Gemini

replace the control

Posted on Aug 06, 2009

Anonymous

  • 1 Answer

SOURCE: Baking Element Caught fire

funny same thing just happened to me and it all seams to be the bottom element of the same ovens around the same year, I bought mine in 99 also, I keep my oven very clean becasue i know the dangers it may cause, I think this is a major problem and it needs to be addressed.

Posted on Dec 11, 2009

Anonymous

  • 713 Answers

SOURCE: Have a Maytag MER5730 oven and the oven stopped

your element is bad replace element.

Posted on Feb 13, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2helpful
1answer

Bottom oven bottom element doesn't heat

Phil. If you do not have voltage at the element, then the Electronic Oven Control ( EOC ) has failed. Part number # 5701M403-60

In order to check for the correct voltage at the element you will need to remove power and pull the range out of its installed location and remove the back panel of the range to gain access to the wiring and element. CAUTION ! I cannot stress this enough ! There are dangerous voltages in this area!! After the panel has been removed, return power to the range,set the lower oven to bake, and check the voltage at the element. You should find 220-240 volts between the element terminals with them connected to the element. If you do not have the proper voltage then you will need to replaced the EOC.
1helpful
1answer

Kenmore electric oven bottom element not working

check thermostate control sensor its locate behind the heating element. check continuty .if its fail .replaced correct value.
GKM
Jan 07, 2014 • Ovens
0helpful
1answer

Oven slow to heat. I had an appliance guy come and change the element, still slow. 1 hour to 300F. I can't find a service manual on this range.

This sounds like a problem with the oven thermostat. If a slow heating problem is reported the element can be the problem sometimes but generally it would be the thermostat which has complete control over the elements heating cycles. It sounds like you may need the thermostat replaced. I hope the the oven door seal it tight. This can cause problems if too much heat escapes through a faulty seal.
0helpful
1answer

Slow to heat on convection mode, bottom element not get as hot as

Check to see that the convection element is heating. If not, ohm it out, either the element is bad or it is not getting power from the control.
0helpful
1answer

I have a whirlpool range mod rf368lxpq o replaed probe and panel still very slow to come to temp. pre heat goes to about 200 deg and then veryy slow to come up to temp and hold temp

It sounds like one of the elements are not working. There should be a concealed element in the bottom of the oven and a 'bake assist' element at the top iether seperate from the grill element or as a dual element assembly. Both of these elements should heat on bake function (not the grill element though), check for heat from both by turning bake on and feeling for heat from top and bottom. The oven requires heat from bot to get up to and maintain temp.

Hope this helps
0helpful
1answer

JBP66G W1AD Oven won't get hot enough

the yellow may be the oven temp sensor?
Not finding what you are looking for?

190 views

Ask a Question

Usually answered in minutes!

Top Maytag Kitchen Ranges Experts

vince

Level 3 Expert

1536 Answers

Cindy Wells

Level 3 Expert

6586 Answers

Marvin
Marvin

Level 3 Expert

85241 Answers

Are you a Maytag Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...