New out of box,My remotes will not work when my LED light on the out side of my house are on

light at the remote control flashes; does not mean it works properly. You have to check whether it emits infrared rays out from its front; which activates the TV. The indicator light blinks; means the remote control is working, and the the batteries are good. That's all. The infrared light that emits from its front side [infrared LED] is not visible to human eye. It can be detected by an electronic camera. If infrared ray emitting LED is faulty, the TV won't respond to remote control.
Check the remote control for its infrared emission. Check it by pressing all the keys. You can detect the presence of infra-red emission from the remote control, using a cell-phone camera. If you wish to get more details about how to check a remote control, please visit this site. One among the posts has details about it. Surf the site with patience. In some cases, the remote control might need to clean.
http://remotesearch.blogspot.com/
Search the site by type in this key phrase "how to test a remote control "in the "search box at the top right of the display window of the Homepage" to get the related post quickly.
https://www.youtube.com/watch?v=jsSCNCW3IbQ [open and clean]
https://www.youtube.com/watch?v=Qp-l1uh-5gE [open and clean]

I found a remote at Radio shack that has been able to address every electronic gadget in my house. It works with the digital convertor box, the vcr, the TV, the VCR, the DVD, and all of the functions work. There will be some reading you must do to get the new remote to "talk" to all the devices, but with a bit of patience, you will get it done. Hope that helps.

Sounds like you need a new transmitter. The light is a battery indicator light.

I had this exact problem. I bought two Home Decorator fans from Home Depot and installed them in separate rooms in my house. They have LED lights. I know for a fact that I wired them right because the model fan in Home Depot fan was wired the same and my remote worked perfectly with that fan. Both fans at my house had the same issue of the light not turning all the way off but dimming worked and fan speeds worked. LONG story short, I had another fan in the Master Bedroom that was turned on. When I turned the power to that fan off (wall switch toggled to off), both of the new fans worked!!! Now I need to figure out how to wire the Master bedroom fan correctly (9 wires in one box) but at least I know what the issue was!

Tries take both remotes controls pushes all the funsctions butons one by one on the front of a turn on Digital Camera,see if u will able to see all the INFER RED signal white light will flashing on the Digital Camera viewing screen.To make sure both the remotes are working and all the buttons are have INFER RED light signal out.Tries pushes all the tv manual buttons on the tv side too see if it is funsctioning too.If all these work testing work,than take some rubbing alchahol put on a rag clean the INFER RED sensors signals on the tv an the cable box by the tv power light LED indications lights.Tries these steps,make sure tv manual control tv side panel work and both remotes works and clean both INFER RED sensors on cable box and tv make it work better.Unplug the cable box for an hour for it to reboot and updating it softwares.Replug the cable box and now tries the tv remote or cable remote again,should functions now.

Yes,the tv manual controls board infered signal light from the LED diode,to the tv have problems.Take the tv back where u bought it and exchangce it for another new tv.

I recommend using the code-search function of the Innovage Jumbo Remote for both CABLE and SAT to try and find the one that works with your Time-Warner cable box.

To have the remote try each CABLE or SAT code it knows one at a time, follow these steps:

1. Turn on your cable box.
2. Press and hold the CODE SEARCH button for at least 3 seconds until the red LED lights up and stays lit.
3. Press the CABLE or SAT button on the remote so that the LED blinks once and then remains solid red.
4. Press the ON/OFF button slowly and repeatedly until the cable box turns off. The LED will blink once each time you press the ON/OFF button.
   
5. Once the cable box turns off, press the ENTER button to store the code and the LED will turn off.
   

I hope that helps.

You either have a bad receiver or the receiver isn't wired correctly,

On the receiver house wire side are black, white, and green.

On the receiver fan side are white, black, blue, and green. The black is hot for the fan, the blue is hot for the light. They can be wired together from receiver to fan.

At the bottom are a blue and a white wire to go to the lights.

Sometimes when installed the receiver is placed so that a part of the wiring box obstructs the signal from the remote and it doesn't work properly, or misses some commands.

I recommend buying a new remote and receiver and wiring the receiver in so that it rests on the sheetrock beside the wire in box.

Dont think so
Try resetting it by this method,it might work
To perform a RESET press [TV] and then hold [select] and [red button] together for around two seconds (until the red light blinks twice). Now press 999 (red light blinks once for a long time and then twice quickly).

Please let me know if this helps
JonnieC

I had the problem, after a lightning surge through our house, that destroyed item connected to the telephone lines. The Cinemate interface unit stayed red (powered), but could not get green light to come on, and obviously no audio. Found through Bose tech support that the the units are failing from surges "too often". They are trying to find out why and fix the longterm problem. Tell them you had a power surge (which you likely did), the green light won't come on, but the remote works with TV, etc. They will send a UPS Return Tag for you to send back the small interface unit (only). Upon receipt, they will 2-day air you a new one. It solved the problem.