Question about Fisher and Paykel Aquasmart wl80t65c

1 Answer

Power cut problem during the rinse cycle. Machine keeps cutting out.

Machine won't get past the rinse cycle. Keeps cutting out about 2 minutes into the rinse cycle. Thanks, David

Posted by David Fuda on

Ad

1 Answer

keith jones

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Master:

    An expert who has achieved Level 3.

  • Fisher and P... Master
  • 747 Answers

Check for faulty pump

Posted on Oct 26, 2017

Ad

5 Related Answers

catriver

Ron Marek

  • 878 Answers

SOURCE: Slow Filling only in rinse cycle

Tony, the fact that you are not receiving any error codes tends to leave me to believe that your cold fill hose filter may be restricted. Going by your model number you can enter this mode by having the power on at the source and off at the console. Press and hold the lifecyle button and then push power button. You should hear 2 beeps and then the display go blank. You can test the hot and cold valves by pressing how dirty up (hot) and how dirty down (cold). If you find the cold valve slow as in your rinse check for restrictions. If it were the thermistor, I would think you would receive an error code..Good luck.

Posted on Jun 06, 2006

Ad

Anonymous

SOURCE: Fisher and Paykal GWL 10 US - Stops before rinse

...most likely the balance sensor, a small contact switch behind the main control panel that is telling the machine it is out of balance, more likely the switch and/or contacts have corroded...

Posted on Aug 20, 2007

Ian Greenland

  • 351 Answers

SOURCE: Machine stops during run time & lights keep flashing and beeping

it may be a balance problem

Posted on Mar 03, 2008

Anonymous

  • 998 Answers

SOURCE: FISHER PAYKEL WASHING MACHINE STUCK IN RINSE CYCLE

lift the end of the drain hose see if the tub fills and goes in the rinse cycle if it works you have a syphon problem if so make your drain pipe stand longer.

Posted on Aug 06, 2009

Julie Herr

  • 2 Answers

SOURCE: I have a Fisher & Paykel IW812 Intuitive Eco.

I had the power cut problem too. When I called the repairperson they blamed faulty wiring. I haven't tracked this down to see if this is actually the case.

Posted on Oct 21, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cold water cutoff


Either or Both of the below may be the reason:

(1) Sensors have stopped working.
(2) Something is obstructing Drain System.

Call Customer Service Engineer.

Mar 29, 2014 | Bosch Washing Machines

1 Answer

Cold water won't stop before rinse cycle


if it fails to stop running only at the rinse part of the cycle it is probably in the timer as the solenoid valve has to cut the water off when the washer fills for the wash cycle too. fills for wash cycle and cuts off water, washes and drains, refills for rinse cycle and water just keeps running? does this every time you run it? that's in the timer. bad solenoid (water inlet valve) would keep running even on wash fill up. hope this helps.

Feb 25, 2014 | LG WM2688H Front Load Washer

1 Answer

Start matsui washing machine


Check the washer drain hose for clogs.

Jun 19, 2017 | Washing Machines

2 Answers

What causes the manitowoc ice machine to cut off during the freeze cycle


most of the problems on ice machines is a restriction in water circulation due to no maintenance. Might need some cleaning to be done.

Apr 19, 2013 | Manitowoc SY0854A Self Contained 870 lb...

1 Answer

Rinse and spin cycle keeps repeating at 11 minute time to 17 minute time and won't stop


Sounds like your washer does not empty enough water for the spinning to stop. Have you check that the filter(s) are not clogged?

Jan 23, 2013 | Samsung WA5451ANW 4.7 cu. ft. Top-Load...

1 Answer

Washer won't go into spin cycle, stops after final rinse. When I try drain &rinse it still will not spin.


If the unit does not spin correctly, this is usually an indication that the unit can also not drain. The unit will not spin if it senses a blockage or issue with the drain lines and/or pump. Try to check the drain lines in the back of the unit for any issue, and then see if you have an access panel to get to the coin trap or drain pump itself. Often socks and debris will clog up in this area and cause your problems.

Dec 25, 2012 | Frigidaire ATF6000ES Front Load Washer

1 Answer

Fisher and Paykel 7.5 washing machine keeps powering off during rinse and spin cycles


The pump has a thermal safety cut out on it.
If the pump gets too hot it cut out.
Just put a new pump in and your all going again.

Aug 05, 2012 | Fisher and Paykel Washing Machines

1 Answer

Washing machine cuts out


The pump is over heating and cutting power.

Mar 30, 2012 | Fisher and Paykel Washing Machines

Not finding what you are looking for?
Fisher and Paykel Aquasmart wl80t65c Logo

Related Topics:

339 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fisher and Paykel Washing Machines Experts

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

peter gittos
peter gittos

Level 2 Expert

247 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Fisher and Paykel Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...