I have a frigidaire stove top model GLEFZ384CHA. I got the F10 code on my range so I replaced the oven temp probe. Still getting f10. Only broil element coming on, even when bake button is pushed.help

I am 99% positive you need a new EOC based on the fact that you said you heard the all too common pop noise. EOCs usually cost around $200-$300 and sometimes more. The EOC in this is the same as your clock, if you took off the top back you will see burn marks on the back of the clock.

Good Morning Irene, thank you for allowing me to assist you!

The F10 and F30 error codes are in regards to an open or failed oven sensor. If the sensor and EOC has been replaced, more than likely a professional would need to inspect the wiring harness between the EOC and sensor.

Best regards!

Hello - Typically error code F10 could indicate a variety of issues. The range could possibly have a runaway temp (higher than normal temps), shorted keypad, faulty EOC (Electronic Oven Control) or, display wire harness missing/not connected. Usually, this code means to replace the EOC. You may be able to reset the range by disconnecting the power to the unit for up ten minutes. Usually this will clear most false error codes. You can disconnect power by either unplugging the unit or flipping the circuit breaker off and back on. If resetting the unit proves to be ineffective, I would recommend contacting a professional to move forward accurately.

Hello,

The F10 error code means that a button on the touchpad is stuck.The error code can be cleared by pushing the cancel/off button and if the F10 returns the clock needs to be replaced since on that model the touchpad is part of the clock.


GENE

hello there"
The "F10" error code caused by the runaway temperature.

The first thing I would check is the resistance across the oven temperature probe (aka oven temperature sensor) terminals at the EOC (electronic oven control) plug.

It suppose to be about 1100 Ohms at the room temperature.

If the resistance at the EOC plug is wrong, then measure the oven temperature probe resistance at the probe plug.

If it's wrong - replace the oven temperature probe. It's better to hardwire it, using a high temperature ceramic wire nuts.

If the readings at the EOC and at the oven temperature probe plug are different - check the wire harness between the oven temperature probe and the EOC.

If there is nothing wrong with the oven temperature probe resistance - replace the EOC.

- The part number for the oven temperature probe is AP3704441

- The part number for the EOC is AP3776874

- The part number for the EOC overlay is AP3778486


Read more: http://forum.appliancepartspros.com/oven-repair-including-ranges-cooktops/4431-f10-error-code.html#ixzz156CO7RjB

Frigidaire stove
(F10 only) Check RTD Sensor Probe & replace if necessary.
If oven is overheating, disconnect power. If oven continues to
overheat when the power is reapplied, replace EOC. Severe
overheating may require the entire oven to be replaced should
damage be extensive.


If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

need model number to what f10 relates to .

Open (F30) or shorted (F31) RTD sensor
probe/ wiring problem. Note: EOC may
initially display an "F10", thinking a
runaway condition exists.

1- Press Cancel key.
2- Check wiring in probe circuit for possible short or open
condition. Check RTD resistance at room temperature
(compare to probe resistance chart). If resistance does not
match the chart, replace the RTD sensor probe. Let the oven
cool down and restart the function.
3- If the problem persists replace the relay board.


If you need further help, I’m available over the phone at https://www.6ya.com/expert/craig_3fa289bf857b1a3c

Hello
Welcome ,

F10 Runaway Temperature.
(F10 only) Check *RTD Sensor Probe & replace if necessary. If oven is overheating, disconnect power. If oven continues to overheat when the power is reapplied, replace EOC. Severe overheating may require the entire oven to be replaced should damage be extensive.

You will need a professional diagnoses to determine the extent of this damage

Thank You Huum

Please remember to leave a solved rating before you sign off!

replace the oven probe in the oven its the gold looking piece sticking out inside the oven