My RDT300 will not respond to my remote. I tried

Direct Code Entry

1. Press and hold the SETUP button until the red indicator stays on, then release the SETUP button.
2. Press and release the desired Mode button (TV, VCR, etc.). The red indicator blinks, then stays lit.
3. Enter the 4 digit code from the code tables. Note: after a valid code entry, the red indicator turns off. For an invalid code, the red indicator flashes.
4. With your device on, press CHANNEL UP. If the device responds, no further programming is required. Note: If some buttons do not operate your device, try one of the other codes for your brand.

Remote Codes ' MyDISH ' DISH Customer Support

https://www.mydish.com/support/remotecodes

Remote Control Manuals · Program Remote to TV/Other .... remote, product type, and manufacturer below to see the current known remote codes you should try.

My Dish remote needs programming for Sanyo TV ... - Directly

https://www.directly.com/.../dish-network-my-dish-remote-needs-progra...

My Dish remote needs programming for Sanyo TV, Model DP226649. My Dish ... Needcode. Alta asked this ... Dish Network • 16808 answers • 95% helpful. Code is ... Test volume control, if it works you're set ... try 590 it should work. tivosat.

How do I program my dish remote to work for my Sanyo TV.

https://www.directly.com/.../dish-network-how-do-i-program-my-dish-re...

Dish Network. How do I program my dish remote to work for my Sanyo TV. ... entercode 590 press pound then sat Then try to turn tv on and off then try volume.

How do you program a dish network remote to my sanyo tv? ' Ya

First, try pressing TV on the remote, check if that solves the problem. Then press Sat and try the TV power button again. If the remote previously controlled the TV, you lost the code for the TV. If you have your Dish Network manual, check if you wrote down the code when it was originally programmed. Which specific remote/receiver do you have? The programming directions and code lists are available here: http://www.dishnetwork.com/supportsection/remote-setup . You can also scan all of the codes to find the correct one: see http://www.dishnetwork.com/SupportSection/power-scan-instructions . Additional remote/receiver manuals are here: http://www.dishnetwork.com/SupportSection/manuals .

The direct coding procedure for the Dish remote that I have is: while facing the TV to be controlled (after adjusting the key for TV1/TV2 in a multiple TV system), press and hold TV until all four indicators light up. Then enter the 3 digit code. Press and release the # key. Then see if the code TV powers off when you press Power. Then press Sat and check if the TV power button works. Try additional codes if the TV doesn't respond.

If you recently got a new TV and you tried to program the remote for your TV, your dish remote may not have the code you need. (Most universal remotes are limited to codes for devices released 6 months or more before the remote was programmed.) In that case, you should use the TV remote (and see if it has an option to control the satellite receiver). Alternatively, get a new universal remote that will control all of your devices. (The remotes that can be programmed by USB are the easiest to set up.)

I hope this helps.

Cindy Wells

ablesmichell

What are you trying to program your remote to? I have provided a link to the steps for programming the remote to your TV or receiver. If you are trying to program to another device, please respond to this site. If you are trying to program to your TV, I have also provide a link with the different codes for each type of TV. I hope this helps.

Remote instructions: http://www.dishnetwork.com/SupportSection/remote-setup
Remote codes:
http://tech.dishnetwork.com/departmental_content/techportal/content/tech/remotes/TechRemo5.3Code.shtml

Ray Calo
DISH Network

Hey there! This is Becki Barned, with Dish Network customer service! The problem that you may be having is with interference with the remote. Depending on how much light is shining directly on the receiver, such from a lamp in the evening, or the sunset, this can interfere with the remote responding to the receiver. If you have glass in front of your receiver, that can cause it too. Try to remove all objects or lights from the front of the receiver, and it should work fine!

rpallot,

I have provided a link on how to program the DISH Network remote to the Samsung TV. The link is:

http://www.dishnetwork.com/SupportSection/remote-setup

A link for the remote codes is also included.

http://tech.dishnetwork.com/departmental_content/techportal/content/tech/remotes/TechRemo5.3Code.shtml

I hope this helps. If you have any other questions, please respond to this link.

Ray Calo
DISH Network

Since you dont have a popular brand set you should try using the scan method. Here is a link with a video to help program your dishnetwork remote to work with your set. http://www.disheez.com/videos/dish-network-video/programming-dish-network-remote/

All you need to do is a manual code search on the dish remote. If it does not respond with the manual code search,the remote your trying to use cannot be used for this TV set,or you will need to upgrade to a differant Dish remote as the code is not programmed into the remote. What happens when you do a manual code search is one by one the remote sends out every single code that is programmed into the remote. Good Luck