Question about Philips Magnavox MWR20V6 DVD Recorder/VCR

Open Question

Red power light blinks for a second when standby-on button is pushed, but power won't stay on.

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

SOURCE: Blinking red light, doesn't turn on Philips 32".

count the blinks from the red led this number will tell you the stage of the poss fault

Posted on Jul 26, 2007

Ad

Anonymous

SOURCE: philips - dvp 642/37

Player goes back to standby because the power supply still has a problem.Run checks on semiconducters in primary cct. of chopper transformer.If ok, replace the pulse width modulator.That should fixya.

Posted on Jul 23, 2008

Ad

GySgt2u

  • 63 Answers

SOURCE: I can't get my tv to turn on... nothing but blinking red light

Thats nots it its bad caps.....

need to replace 3300uf 10V with 3300uf 16v or higher. A couple of bucks in parts and some soldering.

Fixed both of my 50" sets

Posted on Feb 16, 2009

Anonymous

  • 1077 Answers

SOURCE: will not turn on

This might help you. Try starting on page 27 of this:
http://www.scribd.com/doc/6528782/Philips-42pf7320

Posted on Apr 05, 2009

Anonymous

  • 1077 Answers

SOURCE: Set will not power on.. Blinks red LED 8 times

It's a power supply related problem.
The flashing 8 times is a trouble code. A Service Manual for your TV model will have the info on the codes. It could be a bad capacitor or a transformer on the power supply board.If you have some electronic experience, you can find a Service Manual for your TV over the internet. Cost about under $20.

Posted on Jul 31, 2009

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I replaced the power board on my Scott TV LCT37SHA. when I press the power button the red light blinks as I push it. if I hold down the power button it just blinks until I let it go. please help!!


These blinks [flashes] are fault indication (Error Codes). From the number of blinks occur at one time switch ON, you can get an idea about the faulty circuit section inside it. This will make repair easy. These are called blinking codes. Make sure about the exact number of blinking of the standby/power LED, by switching On & OFF the set, for at least two times. Count it carefully. If you wish to get some details, check the site linked here. It has details about blinking codes, and fault locating procedure, to many popular brand TVs and other devices. http://electronicshelponline.blogspot.com/

Jan 18, 2015 | Scott Televison & Video

1 Answer

I'm assuming that it is an error code. The red


colour wheel issues and defective lamp replacing lamp and light engine color wheel cos its worn out

Jul 07, 2013 | Televison & Video

1 Answer

My toshiba TP48E60 model projection tv won' turn on, power light just blinks


Blinking of power LED are fault indications. Count the number of blinks occur at one time switch on. For this number, you can get an idea about the faulty section circuit inside it. It will make troubleshooting much narrower. If you wish to get more details about the blinking codes, check this link. Pull up older posts there.

Mar 08, 2013 | Televison & Video

1 Answer

TV won't turn on


Before going OFF, the standby LED might blink. These blinks are fault indication. The number of blink should be counted. Count the number of blinks at one time, before the TV goes OFF. [eg: 4 blinks Power SOS P Board; 6 blinks Driver SOS 1 SU / SD / SC Boards
(SC energy recovery circuit)] and so on. you can get more details from this site named 'Electro-help'. You can reach it by searching the keyword "electronicshelponline" by internet.

Jul 03, 2012 | Panasonic TC-P50X1 50 in. Plasma HDTV

1 Answer

Start button not working standby light staying


The switch is for 'REC' 'Standby' and "PLAY".
If you leave it switched to "Play" and pull the plug and push it in to the wall receptacle (mains) it should start playing after a few seconds delay. The same for "REC". You use a timer unit on the power cord for those.
If you have the switch in the middle position and plugged-in, you should have a tiny Red LED illuminated. Push "Power" and it should start-up and be ready to use in a matter of a few seconds.

Feb 22, 2009 | Sony MDS-JE520 Mini Disc Player

1 Answer

Samsung hc-r5245w no power


Hello Chac c,

The reason that you are getting a 'red light' is because your lamp is burned out. There is a panel on the back of the TV that gives you access to this lamp. You can remove it and check the part# to be sure then replace it. I did a quick search for you just based on the model# which you provided. You can see it here - http://www.nextag.com/serv/main/buyer/OutPDir.jsp?search=samsung+lamp&gg_site=&gg_aid=1295966762

Hope this helps :)

Mar 17, 2008 | Samsung HC-R5245W 52" HDTV

Not finding what you are looking for?
Philips Magnavox MWR20V6 DVD Recorder/VCR Logo

Related Topics:

138 people viewed this question

Ask a Question

Usually answered in minutes!

Top Philips Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76443 Answers

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

matt martin
matt martin

Level 3 Expert

1258 Answers

Are you a Philips Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...