Question about Frigidaire GLTF2940ES Front Load Washer

Open Question


Thi unit door unloc in the middle of cycle



1 Related Answer


Richard Roth

  • 9472 Answers

SOURCE: my washer is loc and

The Control Lock (child lock) is on: To prevent accidental operation of the washer or alteration of the cycle settings, press and hold the lock symbol until you hear 3 beeps and ?LOC? is displayed.

To cancel, press and hold the lock symbol until ?LOC? is no longer displayed. To put the control into control lock you do the same thing.

Posted on Jul 30, 2011


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

My daughter leant against WDL520 washer dryer whilst in middle of a cycle and it stopped, door light is flashing and making a clicking noise when I try and put a new cycle on

electronics can fail at anytime your daughter leaning on it was coincedence. as this can not in anyway cause a fault. the system has shut down due to a fault within the unit try un plugging it for an hr and plug it back in if there is no responce then it nneds to be looked at by a service tech there is no other quick fix

take care

Sep 12, 2011 | Washing Machines

1 Answer

My friidaire washer will not start. The door lock light will not come on. The door closes properly. The error LOC comes on. Not sure what else to do. Doesn't seem to be any problem closing the door. Help...

To avoid having someone accidentally start or stop the
washer, press Options and Select at the same time and
hold for 10 seconds until “LOC” is displayed alternately
with the estimated cycle time. To unlock the controls,
press Options and Select at the same time and hold 10
seconds until ”LOC” is no longer displayed.

If you need further help, reach me via phone at

Apr 03, 2010 | Frigidaire ATF6000ES Front Load Washer

1 Answer

PLEASE HELP. Dead battery on 1989 BMW 3series with power locks.

Why dont you call loc smith to unloc the doors
You could take flat screw driver to try push the latch side ways where it latches

Jul 29, 2009 | 2001 Porsche 911 Carrera

1 Answer

Upside down F and E error message any ideas?

would that look like a tE or dE? TE is Thermistor error. Replace thermistor and check wiring back to control board. thermistor is accessible from bottom of unit reaching up to bottom front of tub. in middle of heater element it just pulls out of rubber seal.
DE would be a door error. is door open or did it lock when cycle started. door lock asm should fix this.

Jul 05, 2009 | LG WM-2277HW Front Load Washer

1 Answer

1997 tahoe loc code

remove the radio it has a # on the back of unit and call the dealer with that #

Mar 09, 2009 | Oldsmobile 98 Cars & Trucks

1 Answer

I need direction on how to start the clean cycle on my jenn air

Use to set a self-clean cycle or a delayed
self-clean cycle. One press of the Clean
pad sets up an immediate clean cycle. A
second press of the Clean pad sets up a
delayed clean cycle.
• Clean oven
frame, door
frame (area
outside of gasket)
around the
opening in the door gasket with a nonabrasive
cleaner such as Bon Ami*. These
areas are not exposed to cleaning temperatures.
• Remove air grille.
• Remove oven racks. If racks are left in
during a clean cycle, it may impair function
and they will discolor. Turn off the
oven light and close door.
* Brand names for cleaning products are
registered trademarks of the respective
1. Press Clean pad once.
2. Press the Auto Set pad for 3 hours of
cleaning time, press again for 4 hours
and again if 2 hours of clean time are
3. CLEANING and LOC plus the clean
time will appear in the display.
4. When the clean cycle is complete,
CLEANED will be displayed. LOC will
remain on until the oven has cooled
(approx. 1 hour).
5. When the oven is cool, LOC will no
longer be displayed and the door may be
6. Wipe out the oven interior with a damp
cloth. If soil remains it indicates the
cycle was not long enough.

1. Press Cancel pad.
2. If LOC is NOT displayed, open oven
door. If LOC is displayed, allow oven to

Thanks for using Fix Ya, Please take the time to rate this solution.


Feb 08, 2009 | Jenn-Air JDS9860A Dual Fuel (Electric and...

1 Answer

LOC for oven door is unable to unloc

Put the oven in Self Clean mode for 3 minutes and then cancel.. if if that will release the relay that controls the lock. If that doesn't work, Unplug the oven for 10 mintues, then plug it back in holding the CLEAR button down. If neither of those work you will need to contact a service repair man.

Jul 19, 2008 | Ovens

1 Answer


If you have a multimeter check for resistance on the lock motor. Can access from the back by taking the panel off.  Make sure you unplug the range first.  If the lock shows open then it is bad and causing your problem.  Most likely this is your problem.  The motor has to be good for the oven to work.  Let me know what you find.

Oct 21, 2007 | Hotpoint RB787 Electric Kitchen Range

1 Answer

My oven says LOC and it is not locked

Today the "Loc" light came on and I can not use
the oven... the oven door does open and the
cook top works ok?
I see two others have the same problem.
I tried to un-plug the electric plug but this did
not re-set it?
This unit is about 7 years old. I can not find
the manual. There is no re-set button anywhere
and I also can not find a model number on back?

Oct 18, 2007 | Kenmore 95680 / 95681 / 95682 / 95684...

10 Answers

LOC for oven door is unable to unloc

If wiring to door lock motor are ok then the motor may need to be replaced. Need to check the resistance of the motor with a meter. If it checks open then the motor is bad.

Oct 03, 2007 | Frigidaire GLEFM385D Electric Kitchen...

Not finding what you are looking for?
Frigidaire GLTF2940ES Front Load Washer Logo

Related Topics:


Ask a Question

Usually answered in minutes!

Top Frigidaire Washing Machines Experts

Dan Webster
Dan Webster

Level 3 Expert

8221 Answers

Gerry Harvey
Gerry Harvey

Level 3 Expert

1482 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Are you a Frigidaire Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides