Question about Emerson EWR20V5 DVD Recorder/VHS VCR Combo - Salvage/Replacement Parts Only

1 Answer

Can you direct me to a source to purchase the front cover fro this model?

Posted by Timothy Brinson on


1 Answer

Mark Sandmeyer

  • Level 1:

    An expert who has achieved level 1.


    An expert who has answered 20 questions.


    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 24 Answers

You could at salvation army stores and good will if you find one it would be a low cost replacement parts or try Craig's list.

Posted on Aug 14, 2015


Add Your Answer


Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need two of the small covers for the dials on my scope. 3-9x32 #629A

Hello, Joan -

Is your scope a Tasco rifle scope? If so . . .

If you have not already contacted Tasco directly to find out if they sell covers for your model scope, you can find the company contact information here:

Make your telephone call during weekday office hours.

If you cannot purchase the covers from Tasco, I refer you to this online firearms forum where there will probably someone who can either sell you the proper covers or direct you to a source:

You will have to sign up (free) to post any question on the forum.

Best wishes.

Jan 13, 2018 | The Optics

2 Answers

Replacing the back of a psp

Please consult those instructions in the following URL.
If you find this solution useful please rate it as solved.
Thank you

Oct 20, 2007 | Video Game Consoles & Games

1 Answer

Swing motor not working

These are quite easily damaged and sometimes just wear out. The cable from the motor can also be easily damaged. They are cheap and easy to replace. Just source a new one for that model online. When you receive it, turn off power to the system, take the front cover off, unscrew inside tray from cover box, slide tray out, remove the power box, get access to the motor and replace. Be sure to check which wires go where before removing and take photos or make accurate diagrams with color codes. Check that the control board functions normally before purchase though. A faulty board could cause this fault.

May 04, 2014 | LG Electronic Window Air Conditioner

1 Answer

Need to replace the pull cord on model 917376480

Is this the engine model? Is it Briggs and Stratton? You will need to unbolt the cover or drill out rivet's to get cover off. Once removed you will see where cord enters. Go to a hardware store and purchase bulk cord same length or slightly longer than original. Install cord and tie off in a knot like original then wind in same direction as it was, then wind assembly in tension direction of spring( a few turns) then thread cord out hole in cover, put it through handle and tie it off in knot. Then reinstall cover.This can be tricky and you may get direction backwards at first, but don't give up, you can do it. Good luck!

I’m happy to assist further over the phone at

Aug 01, 2013 | Craftsman Garden

1 Answer

The belt fell off, looked worn so purchased a new one and put it on (very tight!) Started machine, and belt new belt fell off. Pls help.

Can you confirm your model number? FAV6800A or FAV9800A?

If it's one of those models with 120VAC power cord removed from the service outlet and the front cover removed. See if you can rotate the Clutch Pulley CW the wash agitate direction and then CCW the Spin direction. The Clutch Pulley is the large pulley in the center of the washer. We are looking to see if the drive system is seized.

After the drive belt replacement was there any belt screech when you powered up the machine and selected a Wash or Spin Only Cycle?

Feb 09, 2011 | Maytag Neptune FAV6800AW Top Load Washer

1 Answer

Where can I obtain spare anti scale filters fro the Breville Steam Generator IIN 195?

I had to ring Breville direct as was having trouble finding them and they said as it was purchased from Argos they will have them - so went to contact argos & found this website - hope this helps

Oct 15, 2010 | Breville Irons

1 Answer

How hard is it to change the lamp on a sony rear projection tv. The model is a 42we655

Very easy,looking fro the front go to the right end clip off the vented cover reach in swist handle counterclockwise pull out that cover reach in lift up little handle then pull out the lamp then the opposite to put back in,hope that gets it!

May 26, 2010 | Sony Grand WEGA KDF-42WE655 42" Rear...

1 Answer

Hitachi Lamp Light Came on

Good Day, CCooke;
Lamp Number for the 55V825 Model is; UX21516.
To replace LAMP remove Front Panel outwards until the quick snap disengages. There is small cover on the left hand side, using a philips screw driver; remove. Two more screws secure lamp, use handle to remove. ALWAYS, unplug TV from A/C power source first. Good Luck, big IRISH.

Sep 03, 2008 | Hitachi UltraVision CineForm 55VG825 55"...

Not finding what you are looking for?
Emerson EWR20V5 DVD Recorder/VHS VCR Combo - Salvage/Replacement Parts Only Logo

Related Topics:

76 people viewed this question

Ask a Question

Usually answered in minutes!

Top Emerson Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76416 Answers

matt martin
matt martin

Level 3 Expert

1258 Answers


Level 3 Expert

5700 Answers

Are you an Emerson Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides