Question about Hobart HL600 Legacy Stand Mixer

1 Answer

What is the error code b-in

The error b-in appears on error screen I want in details to describe me what is it

Posted by Mahmoud fawzy Irahim on

Ad

1 Answer

vestxre

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    New Friend:

    An expert that has 1 follower.

  • Hobart Expert
  • 120 Answers

It's meant to tell the operator that the bowl is not in proper operating position. If the bowl is in the proper position then the bowl in switch may be bad.

Posted on Sep 23, 2015

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i find a rewire diagram for coffee machine, do you have one


What is the brand name to your coffee machine? Provide more details, please. If you wish to get some details; check the site linked here. Pull up older posts. Surf the site with patience. http://electronicshelponline.blogspot.com/

Dec 01, 2014 | Food Mixers

1 Answer

Oven wouldn't turn on, screen said F2E1


If you have a KitchenAid range, the F2 E1 code indicates a keypad problem. If it recurs and continues to give the error after you press Cancel, then you will address the issue. The cake pan position has very little to do with the error.

The fix could be as simple as finding a damaged conductor in the wiring harness and using a conductive silver pen (or use the rear window defrost repair kit liquid applied with a needle and not a wide brush) to repair the break. On some ranges you might need to replace the keypad. Other models have the keypad integrated into the ERC (clock and entire control panel).

I hope this helps.

Cindy Wells

Dec 03, 2012 | KitchenAid Food Mixers

1 Answer

Everything works except nothing heats !!


You haven't described what make and model you have. I can only go off what you have described. There is a 90% chance you have a magnetron fault.

Feb 17, 2010 | Food Mixers

1 Answer

What is error code 99 for a hobart HL 600 mixer?


error 99 stands for communication fault between timer board and the sr drive.there are 5 things that can cause this error.1.rs-485 cable disconnected or malfunction 2.1 con monitordisconnected or malfunction. 3.run/stop wiring disconnected or malfunction. 4.timer board malfunction. 5.sr drive malfunction. hope this helps, dont forget to vote, thanks, monomoy

Jan 29, 2010 | Hobart HL600 Legacy Stand Mixer

1 Answer

3rd gear gets rough ...


The symptoms you are describing would lead me to believe that the shifter clutch sleeve (part # 70035-1) is worn out. There's a chance that the gear that engages the clutch is worn as well, but less likely. A significant amount of transmission disassembly is required to access and replace these particular parts. There are a lot of things that can go poorly if you don't pay attention to detail when disassembling/reassembeling the transmission of a D300 (ie clutch rollers and springs) On a brighter note, it's about a 90 minute job for a proficient technician, if everything goes his/her way. That money would be well spent.

Oct 02, 2009 | Hobart D300-6036 Mixer

2 Answers

Oil leaking, sounds like the problems folks are having with the K55 model


Could you please describe the issue in more detail? Thanks.

In the meantime, I will see if I can locate a service manual.

May 23, 2008 | KitchenAid K45SS Classic Stand Mixer

1 Answer

Hobart hl600 mixer


I know what these codes are: code 19 is that phase c is over current fault and code 23 is a motor stall fault.I would start by making sure you 3 phase wiring going into the mixer is there.I service these mixers as im a service tech for hobart.these units are very detailed and i can walk you thru some things to check but if you have an electrical problem you most likley will have to call a hobart service tech because we have special equipment to diagnose the fault.let me know it may be something simple as these mixers are usally maintenance free.

Nov 14, 2007 | Hobart HL600 Legacy Stand Mixer

1 Answer

Appliance Noise Level


Hi if this has been in use long it appears that the bushes have got worn out and there is a "play" between the blade shaft and the body. A temp cure would be to oil the bush, but I am afraid eventually you will have to get it replaced at the dealers.

Sep 05, 2007 | Food Mixers

Not finding what you are looking for?
Hobart HL600 Legacy Stand Mixer Logo

Related Topics:

262 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hobart Food Mixers Experts

Pieter Vleeshouwers
Pieter Vleeshouwers

Level 3 Expert

2027 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Lawrence Oravetz

Level 3 Expert

10548 Answers

Are you a Hobart Food Mixer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...