Question about Washing Machines

1 Answer

Why does the washer stay in the wash cycle?

Washer fills then goes into wash cycle and stays there. It will not move into next cycle. When I open door and bypass switch to watch the cycle it appears to agitate but I can hold the agitator and move it freely. I can place it in another cycle and it will work in that cycle but it will stay in that cycle.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 10 Answers

Water pump stuck or faulty

Posted on Dec 31, 2017

Ad

5 Suggested Answers

Anonymous

  • 20 Answers

SOURCE: Washer fills and spins but does not agitate

Im sorry to say, it sounds like the transmission in the washer may have gone out, the unit it self sits at the bottem of the main agitator shaft under the the tub, you may be able to have this replaced, but shop around for the right price.

Posted on Jan 27, 2008

Ad
IB4G2008

Patrick Michaels

  • 3587 Answers

SOURCE: Washer doesn't agitate

sounds like your washer went mellow on you(doesn't get agitated, right)?

ok. enough humor.

sounds like there's a problem with the motor/belt/control board in that order

Posted on Mar 13, 2008

Anonymous

SOURCE: Agitation issues. Everything else appears/works normally.

I just encountered the same problem. I think the operation of the machine is such that the motor turns one direction for the spin cycle, and the other direction for the agitate cycle. I am replacing my motor, as I think i have a bad winding on the reverse. I will let you know.

Posted on Jul 27, 2008

Anonymous

  • 12 Answers

SOURCE: washer fills but won t advance to the next setting for all cycle

Do you hear the ticking of the dial moving? if so it could be that the points aren't getting connection to cycle it threw the various cycles

Posted on Nov 22, 2008

jumptrout51

steve

  • 3361 Answers

SOURCE: will fill and drain wont agitate or spin

Replace the lid switch.

Posted on Mar 11, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My washer will not switch from one cycle to the next


I understand that your washer is not advancing and stuck on one cycle. If you provide a Model and serial number, it will be helpful.

Jul 22, 2016 | Washing Machines

1 Answer

What could be wrong with our washer So our washer filled up with water and then will not go into the next cycle even if we try to manually do it Do you know what could be wrong


  • Does Your machine have a little switch button activated by the top door? (You can hear it click as you open and close the door.). If that switch is not working, the control click can not let the machine advance to the next step in the cycle.
  • Let US know what you find. M B

Jul 08, 2014 | Kenmore 24032\24036 Top Load Washer

1 Answer

Washer filling problem


Check to hose to the water level control. It goes from the outside of the tub up to the control which is located in the same area as the timer. It's usually round with the end of that tube and at least 2 wires connected to it. Disconnect the hose and blow air through it. Reconnect and try again. Still no fill, try filling with that tube disconnected. Watch it the entire time as with the tube off the water should not stop. If it fills all the way with the tube off the water control unit has a problem.

Jan 07, 2014 | Roper Washing Machines

2 Answers

Washer stops after aggatating and wont drain


My Kenmore 70Series washer goes through the wash cycle then just stops when it is to drain and then spin.

Jun 10, 2009 | Whirlpool Washing Machines

1 Answer

Stays in wash cycle


Solution found in a defective SPDT 'Heater ON' switch which had burnt out, thereby causing an 'open' to pump solenoid, fill valve, and heater. Temporarily bypassing the switch confirms the solution. Buy either the whole switch panel (3 switches) from parts dealer or find a source for CW Industries part GRS2012-13.

May 27, 2009 | GE Dishwashers

1 Answer

My machine quits working during the rince cycle


the safety switch could be the culprit on this because anytime you open the door on top it triggers which turns it all off. so what i would start with is either bypassing that switch or replacing it.

Dec 01, 2008 | Whirlpool Ultimate Care II LSQ9549L Top...

1 Answer

Washer fills but won t advance to the next setting for all cycle


Do you hear the ticking of the dial moving? if so it could be that the points aren't getting connection to cycle it threw the various cycles

Nov 22, 2008 | Whirlpool Ultimate Care II LSQ9564J Top...

1 Answer

Washer refuses to move to next cycle


Can you still open door when it has filled?If so it is intermittant door lock .If no new progame card required.

Nov 05, 2008 | Hotpoint Aquarius WD63 Front Load...

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

50 people viewed this question

Ask a Question

Usually answered in minutes!

Top Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Marvin
Marvin

Level 3 Expert

85223 Answers

Brad Brown

Level 3 Expert

18165 Answers

Are you a Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...