AEG Lavamat W1050 Front Load Washer Logo

Related Topics:

Question about AEG Lavamat W1050 Front Load Washer

Open Question

Machine stops during short cycle without finishing the wash sometimes it stops at the wash phase and other times it stops at the rinse phase. full cycle works fine

Cleaned the filter, removed the inline water filters from the inlet. The end indicator is flashing once only. But no flashes and all well during long cycle.

Posted by Deborah Maddison on

Ad

3 Related Answers

douglas smith

  • 1462 Answers

SOURCE: AEG Lavamat w850 not finishing cycle! help!

check no kink in drain hose and if plumbed in unbder sink, check spigot into sink drain is not blocked. put drain hose lower down band check there is water coming out freely. if not, then suspect something trapped in hose from tub to pump

Posted on Mar 26, 2007

Ad

carsija

  • 1 Answer

SOURCE: aeg 76669 oko lavamat machine not


I have had the same problem. If you switch the machine to off and then to cotton/linen 95, then press at the same time prewash, soaking, qick wash and stain buttons for 10 seconds switch it off. When I switched it on it worked.

Posted on Jun 24, 2008

Ad

Anonymous

  • 6277 Answers

SOURCE: Machine doesn't complete full cycle

Hi from retired Englishman in SW France,

I would gently suggest as a first step that you clean the drain motor/pump lint tray/filter. So many 'faults' are caused by blocked filters and many machines will not even go to rinse or spin or release the door lock if there is any water still left inside.
Following are my complete and hopefully 'coverall' pre-typed guidance notes for checking both the drain motor filter and the drain motor ;-0)
REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT (alternatively use a wet vac as sensibly suggested by VinnyB1234!)
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!). These panels are either held on by (plasic) screws or will just pull off. Most filters are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play.
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Posted on Sep 06, 2011

Testimonial: "Super fast with a solution and correct!"

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
2answers
3helpful
3answers

I have a Miele W1918 washer which has worked perfectly for a decade. Now there is not enough water to fill the tub during the first 'rinse' phase of normal cycles or the 'separate rinse' cycle. The machine...

I have exactly the same problem. I am currently getting around the issue by letting the machine do the washing then at the end of that cycle do a manual rinse cycle.
3helpful
1answer

Whirlpool AWM 5080 stops during cycles

Sound like could be faulty pump however you need to make sure no
Could be pump at fault 1st you need to make sure no coin stuck in there ...




1helpful
1answer

Agitator starts at begining of cycle before washer is full

Please be carful as running the agitator without enough water will overheat and kick out the motor, however it should be ok when it resets itself.
Yes, the machine should stop agitating when you lift the lid so this too is part of the problem.
After looking at the print I can only suggest that the cam contacts in the timer ( contacts 12 and 14) that start the motor are burned and stuck together.
Quentin
0helpful
1answer

Fisher and Paykal GWL 10 US - Stops before rinse

52. (00110100) Eco - Diverter Top-up Fault diverter valve made be stuck in half open position ,may be a mechanical obstuction or the wax filled solenoid that actuates it may be faulty .located under machine beside pump .
4helpful
1answer

GE Nautilus won't drain after Rinse Cycle

Check disposer plug. If a garbage disposer has been recently installed, it is possible the disposer drain plug was not removed. The drain plug is a plastic piece in the disposer that blocks the hole where the dishwasher hose connects. Also check the hose connected to the disposal. Mine apparently had a kink in it. When I straightened the hose the dishwasher drained at full speed (I recently had a plumber re-route a hot waterline. He must has bent the hose). Hope this helps. If not go to the GE website. That's where I found my answer.
0helpful
1answer

Fisher and Paykal GWL 10 US - Stops before rinse

...most likely the balance sensor, a small contact switch behind the main control panel that is telling the machine it is out of balance, more likely the switch and/or contacts have corroded...
Not finding what you are looking for?

78 views

Ask a Question

Usually answered in minutes!

Top AEG Washing Machines Experts

Brad Brown

Level 3 Expert

19163 Answers

john h

Level 3 Expert

28087 Answers

mark warfield
mark warfield

Level 3 Expert

453 Answers

Are you an AEG Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...