Question about Hotpoint Aquarius WD63 Front Load Washer/Dryer

1 Answer

Hotpoint aquarius dryer

Dryer blows cold air, elements not heating up.

Posted by anglia on

Ad

1 Answer

Shaf Ahmed

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 139 Answers

The t-stats have blown.. these are located on the top of the heater on top of the drum.. To check to see if their blown check the continuity if they are blown then there will be no continuity ... They come in a pair and are easily replaced.. All you have to do is take off the lid...

Posted on Nov 14, 2007

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hotpoint Aquarius tvm560 tumble dryer is blowing cold Air can it be fixed


sure it can., check ur heating element, with multimeter, and check ur thermostats the hi-lo the thermal cut off , cycling thermostat, etc.

Jan 28, 2015 | Hotpoint Dryers

1 Answer

Hi I just replaced the element on my hotpoint aquarius it work fine for about 10 minutesthen just went to cold air I checked the element and it seems fine what else could cause this to happen.


Check your thermal fuse. Also, the upper limit thermostat could have taken a nose dive. Another culprit could be the centrifugal switch on the motor, but that's pretty rare. Also, make sure your vent hose and venting system to the outside is clear of any obstructions. That's usually the reason why elements and thermal fuses burn out.

Good luck!

Oct 18, 2014 | Hotpoint tcm570p Aquarius Condensor Dryer...

1 Answer

Blowing cold air


This model dryer has two heating elements, one for the top and one for the bottom, I suspect that the bottom element is burned out. If you want to attempt it yourself then I can send you a service manual that will walk you step by step through the whole dryer.

If you need further help, reach me via phone at https://www.6ya.com/expert/steven_a67ead41eb5fc62a

Dec 11, 2013 | Maytag Neptune MCE8000AY Electric Dryer

1 Answer

Hi I've Got A Hotpoint Aquarius CTD40 Tumble Dryer


that isn't a model number,open the door to the dryer,look around the opening where you put the clothes in and send the full model number,

Dec 21, 2017 | Hotpoint Dryers

2 Answers

The dryer is blowing cold air, no heat.


Find your thermal protection switch. It looks like a big round button with two screws holding it on either side. (Make sure your drier is unplugged!) There will be a wire going from it to the heating element. It is what regulates the temperature, so it doesn't overheat. Unplug the wires off it and check across the terminals with an ohm meter. It should have full continuity. If not, it's your problem. Replace it. Easy repair.

Feb 18, 2011 | Hotpoint Aquarius WD63 Front Load...

1 Answer

Hotpoint aquarius dryer blowing cold air.can it be reset?model tdl32


Check the heating element and thermal fuses for continuety

Mar 19, 2010 | Hotpoint TDL14 Electric Dryer

1 Answer

I HAVE A HOTPOINT AQUARIUS WD62 WASHER DRYER. THE DRYER FAN TURNS ON BUT DOES NOT HAVE ANY HEAT COMING THROUGH, ONLY BLOWING COLD. CAN YOU SUGGEST WHAT NEEDS CHANGING? THANKS - RICHARD S


It will be a faulty thermostat or element more than likely, or a broken wire.
Remove top cover, and you will see the heater manifold over to the right side, there you will see the element and thermostats.
You will need a meter to test them.
Hope this helps.

Jan 10, 2010 | Hotpoint Aquarius WD63 Front Load...

1 Answer

My dryer is blowing cold air. I replaced the


if you hooked up yhe wires on the heating element check the thermostat it will be a oval shapef unit on housing of element and has wires going to it it may be bad.

Dec 28, 2009 | Washing Machines

2 Answers

MY HOTPOINT CONDENSER TUMBLE DRYER NO LONGER HEATS UP. IT NOW OMLY BLOWS COLD AIR


This sounds like the thermostats or heater

ForAll Your Appliance Video Help Visit Apart4u video tutorials

see other tumbledryervideos here



You-Tube video "sfGInKA3yp8" placeholder (do not delete)



Common faults -
1 The heating elements can fail(meaning open circuit)
2 There are cut-outs (T.O.C's) thatmight need resetting
3 The thermostats (stats) can tripout or burn out (meaning opencircuit)
4 Moderntumble dryers also have sensors and pcb's (Printed circuitboards) thesehaveprograms that can fail and circuitry although most should produce an errorcodeshowing you were the fault is.
5 Faultyconnections and burned wires may also bethe fault.

Nov 17, 2009 | Hotpoint Aquarius WMA42 Front Load Washer

Not finding what you are looking for?
Hotpoint Aquarius WD63 Front Load Washer/Dryer Logo

Related Topics:

268 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Washing Machines Experts

gbob59

Level 3 Expert

3063 Answers

Eric Taylor

Level 3 Expert

590 Answers

Richard C Cohen
Richard C Cohen

Level 2 Expert

171 Answers

Are you a Hotpoint Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...