Question about Creative Labs ZEN Vision:M Digital Media Player

Open Question

HowTo???. Remove Rear Cover/Battery Access???. Many Thanks

Need to replace battery/s. How do I remove rear cover?

Posted by Cliff Allbright on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you remove the battery from a 1997 harley davidson low rider fxdl


The seat must be removed first to for access.
Remove negative connection @ frame, and positve connection @ battery.
Remove the lower rear bolt (left side of battery box @ the frame upright)
Remove the upper rear bolt, and swing down the battery box
Remove top cover ,and side cover
Lift battery out and remove negative cable from battery.

Jul 05, 2011 | Harley Davidson FXDL Dyna Low Rider...

1 Answer

Replacing battery on Aston Martin Vanquish


Below is the procedure for an Aston Martin Vantage, perhaps the vanquish is similar?

Removal
1. Power the driver's fully forward.
2. Remove rear compartment cover.
3. Loosen and disconnect battery terminals, earth (- ve)
terminal first.
4. Release rear carpet, studs (x2), move carpet aside.
5. Remove screws (x2), battery compartment cover to
support rail.
6. Remove nuts (x2), battery compartment cover to body.
Remove cover.
7. Remove Torx screws (x4), remove battery clamps (x2).
8. Disconnect battery vent tube.
9. With assistance, remove battery.
Installation
1. Clean battery tray and clamps.
2. With assistance, install battery into its compartment.
3. Connect battery vent tube.
4. Position battery clamps (x2), install and torque tighten
Torx screws (x4).
5. Ensure battery vent tube is not distorted by battery.
6. Install battery terminals, tighten terminal nuts to correct
torque.
7. Install battery compartment cover, install and tighten
screws (x2) and nuts (x2).
8. Position rear carpet, secure with studs.
9. Install rear compartment cover.
10. Reposition driver's seat.
Courtesy of pistonheads.com

Please vote if this helps! Thanks, Mike

Jun 12, 2011 | Aston Martin Vanquish Cars & Trucks

1 Answer

Hallo, is there a link for an online guide that shows me how to replace the battery of my iriver140? It wount charge, as it only gets warm! Thanks!


Hi, 1) Make sure the player is switched off and the hold switch is on.

2) Remove the screw from each side cover.

3) Remove the 4 screws from each end cap and then remove end caps.

4) The rear cover and side covers can now be removed and the battery removed from the rear cover.
Note: The battery will most likely to be stuck to the rear cover and care should be taken not to put excessive force onto the battery wires when removing the cover. The internal microphone is mounted on one of the side covers and care should also be taken with it so as not to damage the wires.

5) The hard drive can now be removed by lifting and gently pulling it out.

6) Remove the six screws holding the mother board to the front cover. the circuit board may now be removed.
It is a good idea to take note of the routing of the battery wires before removing the mother board.


7) Disconnect the molex plug from the board , this is made easier by lifting the rear of the plug as you remove it.

8) check the polarity of the new battery is the same as the original (they are rarely wrong and need changing).
If it requires changing the terminals can be released by lifting the tags as shown here in the h3xx battery replacement thread.

misticriver.com/iriver-pl...tml#post347705

9) Reassembly is the reverse of disassembly taking note of the following:
a) Check the battery wires are correctly routed to avoid pinching and damage.
b) Check the hold switch slide is aligned with the switch when refitting the side cover.

Have a nice day......

Mar 04, 2011 | iRiver iHP-140 MP3 Player

1 Answer

How do you remove the rear cover to replace the battery on a rado ceramic mans watch ?there doesn't appear to be any access slot, where on many other watches a small grove allows a tool to be inserted...


the cover doesnt appears on the back side of the watch it is engraved with the main body of the watch,take it to a sevice centre they have tools through which the back cover gets separted with the main body of the watch

Feb 26, 2011 | Rado Maxi R21347712 wristwatch

1 Answer

Trying to remove the battery from my 2007 soltice


Hello robert.... Battery Replacement

Removal Procedure

Disconnect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .

Remove the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Lower the vehicle.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable (1).

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.
Notice: Refer to Fastener Notice in Cautions and Notices.

Install the battery hold down retainer and bolt. Tighten the bolt to 25 N·m (18 lb ft).

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts. Tighten the bolts to 20 N·m (15 lb ft).

Install the positive battery cable (1).

Tighten the positive battery cable bolt. Tighten the bolt to 17 N·m (13 lb ft).

Close the positive battery cable connection cover.

Install the wheelhouse liner. Refer to Wheelhouse Liner Replacement - Front .

Connect the negative battery cable (2). Refer to Battery Negative Cable Disconnect/Connect Procedure .


Joe
Thanks for choosing Fixya!

Jan 30, 2011 | 2007 Pontiac Solstice Convertible

1 Answer

How to replace main heater fan


Blower Motor REMOVAL & INSTALLATION Front Fig. 1: Front heater blower motor assembly 89696g02.gif
Remove the glove box to access the front blower motor, which is on the firewall 89696p02.jpg
The blower motor is retained by four bolts (arrows) 89696p03.jpg
The blower motor vent tube helps to cool the blower motor for efficient operation 89696p04.jpg
Push up on the clip to remove the blower motor connector 89696p05.jpg
A ratchet with extensions makes removal of the retaining screws easier 89696p06.jpg
Lift the blower motor over the control cable . . . 89696p07.jpg
. . . and remove it from the vehicle 89696p08.jpg
  1. Disconnect the negative battery cable.
  2. Open the glove box door. Gently squeeze the retainers at the rear of the box inward and allow the box to swing downward. NOTE: If additional access is required, unfasten the glove box hinge retainers and remove the assembly.
  3. Label and disconnect the electrical harness from the blower motor.
  4. Remove the blower motor housing tube and/or blower motor cover.
  5. Remove the blower motor retaining screws.
  6. Remove the blower motor from the A/C evaporator. To install:
  7. Install the blower motor in the A/C evaporator and tighten the retaining screws securely.
  8. Install the blower motor housing tube and/or blower motor cover.
  9. Connect the electrical harness to the blower motor.
  10. Reinstall the glove box and close its door.
  11. Connect the negative battery cable.
Rear Fig. 2: Service cover push pin locations 89696g03.gif
  1. Disconnect the negative battery cable.
  2. Remove both rear passenger seats.
  3. Remove the three push pin retainers from the lower edge of the auxiliary heater and air conditioning service cover.
  4. Lift the service cover outward and upward to remove.
  5. Label and disconnect the electrical harness.
  6. Remove the blower motor housing tube.
  7. Loosen the three retaining screws and remove the blower motor. To install:
  8. Install the blower motor and tighten retaining screws securely.
  9. Install the blower motor housing tube.
  10. Connect the electrical harness.
  11. Position the service cover and install the three push pin retainers from the lower edge of the cover.
  12. Install both rear passenger seats.
  13. Connect the negative battery cable.
prev.gif next.gif

Dec 19, 2010 | 1998 Ford Windstar

1 Answer

I need to replace the driver's side brake light.


Rear Combination Light- 2007 might vary from these diagrams:
Removal & Installation 2004 (Early Production) 4 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear Combination Light kia-06-18-7495.gif

  3. Remove 2 screws and 2 nuts and remove light assembly.
To Install:
  1. Install light assembly and 2 screws and 2 nuts.
  2. Connect electrical connector.
  3. Connect battery negative cable.
5 Door To Remove:
  1. Disconnect battery negative cable.
  2. Disconnect electrical connector. Rear combination light kia-06-18-7496.gif

  3. Remove 2 screws and push light assembly toward outside of vehicle. CAUTION
    Use care to not damage gasket.
  4. Pull rear combination light from vehicle.
To Install:
  1. Install rear combination light and 2 screws.
  2. Install 2 screws.
  3. Connect electrical connector.
  4. Connect battery negative cable.
2004 (Late Production), 2005-2009 To Remove:
Turn Signal Lamp kia-06-20-7698.gif

  1. Disconnect battery negative cable.
  2. Remove 2 screws and cover inside trunk.
  3. Remove 4 nuts and disconnect electrical connector (A).
  4. Remove rear combination lamp.
To Install:
Turn Signal Lamp kia-06-20-7698.gif

  1. Install rear combination lamp.
  2. Install 4 nuts and connect electrical connector (A).
  3. Install cover inside trunk and install 2 screws.
  4. Connect battery negative cable.
prev.gif next.gif

Oct 28, 2010 | 2007 Kia Spectra5

2 Answers

Dead battery


Removal Procedure

Disconnect the negative battery cable

Remove the wheelhouse liner.

Open the positive battery cable connection cover.

Loosen the positive battery cable bolt.

Remove the positive battery cable

Remove the front fender rear bracket to side rail bolts.

Remove the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Remove the front fender rear bracket.

Remove the battery hold down retainer bolt and retainer.

Important: Do not tip the battery more than 40 degrees during removal.

Remove the battery.



Installation Procedure

Important: Do not tip the battery more than 40 degrees during battery installation.

Install the battery.


Install the battery hold down retainer and bolt.

Install the front fender rear bracket.

Install the front fender rear bracket to side rail bolts.

Install the front fender to front fender rear bracket upper (1) and lower (2) bolts.

Install the positive battery cable (1).

Tighten the positive battery cable bolt.

Close the positive battery cable connection cover.

Install the wheelhouse liner.

Connect the negative battery cable

Oct 15, 2009 | 2006 Pontiac Solstice

1 Answer

Battery replacement navman icn530


Remove the 2 small screws and use a tiny flat screwdriver and insert it by where the screws came out and twist. It is clipped down with a series of plastic flanges which can be popped with a twist in between the front and rear case. You need to work your way around the case doing the side with the earphone jack last as the cover needs to slide slightly sideways to slip off. Don't be afraid to use gentle pressure as they will pop apart and wont break

Mar 04, 2009 | Navman iCN 520 GPS Receiver

1 Answer

Cx7330, battery cover BROKEN


Remove batteries and memcard. Remove 8 screws, the screws on the bottom are smaller than the side screws. Rear cover will slide off, watch out for loose LCD screen. Two protruding slots on the bottom hold the battery cover hinges. Hold battery cover wide open and at an angle to snap hinges into place. Reinstall rear cover and screws.

May 29, 2007 | Kodak EasyShare CX7330 Digital Camera

Not finding what you are looking for?
Creative Labs ZEN Vision:M Digital Media Player Logo

85 people viewed this question

Ask a Question

Usually answered in minutes!

Top Creative Labs Audio Players & Recorders Experts

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Creative Labs Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...