Question about Maytag Dryers

Open Question

Error Code 01 F06 - Maytag Dryers

Posted by Tina Rizzo on

Ad

4 Related Answers

JR JR

Johnny Ramirez

  • 116 Answers

SOURCE: Kenmore Elite he3t model 11045972404

POSSIBLE COMMUNICATION PROBLEM BETWEEN MAIN AND MOTOR CONTROLLER

Posted on Nov 30, 2008

Ad

shaun taylor

  • 1527 Answers

SOURCE: error code f06

hello fo6 means drive motor techometer error check wire harness connections between the drive good luck




shaun

Posted on Mar 22, 2009

Ad
jsrock516

Jeff Rockwell

  • 5911 Answers

SOURCE: Error code f06 model 11045089404

"F6" is a Motor Speed error problem. It is commonly attributed to either a broken or slipped drive belt, defective Drive Motor, bad Motor Control Unit (MCU), and/or the interconnecting wiring. The following link explains:

http://www.fixya.com/support/r3608706-f06_error_code

First, remove the back panel of the unit and make sure the drive belt is not broken, or has not slipped off the drum pulley.

Then, remove the top panel of the washer and check all the connector plugs between the Drive Motor, MCU and Central Control Unit (CCU). Check for loose connections and then unplug each connector and plug them back in (one at a time) to ensure they are snug and making good contact. The top panel comes off by removing the three screws that hold it in place in the rear of the washer. With the screws removed, the panel will slide back, then off.

NOTE: You only need to check the connectors that affect the drive motor and MCU circuitry.

The MCU has a tachometer mounted on it. If it is determined to be the cause of the problem, it is considered part of the MCU and cannot be replaced separately. The MCU is not serviceable and will require replacement.

Next, check the motor windings to ensure they are reading the proper resistance. Followed by continuity checks of all the interconnecting wiring between the drive motor, MCU and CCU. You should not need a service manual because each one of these washers comes with a technical data sheet.

For more in depth troubleshooting tips refer to your tech sheet located inside the washer behind the lower toe panel. You will need to locate and remove the screws under the bottom front edge of the toe panel. Once removed, the panel will drop down, then come off. If the tech sheet isn't located directly behind the panel, it will be affixed to one of the interior cabinet walls. The tech sheet includes all error codes, test points, diagnostic procedures and helpful illustrations to assist in troubleshooting and repair of your washer.

Replacement parts (if required) can be purchased at any of the following websites:

searspartrsdirect.com
pcappliancerepair.com
appliancepartspros.com
repairclinic.com

Prices vary between sites, so shop and compare. The first three sites listed also have helpful exploded view parts illustrations to assist you with locating and properly identifying the parts you may need.
If you have any questions, or require additional assistance, please let me know. I hope you find this information helpful.

Posted on May 21, 2010

richroth

Richard Roth

  • 9472 Answers

SOURCE: flashes error code f06

Check the wire harness that goes to all your connectors on the Motor, MCU, and CCU. I have seen a loose wire connector do this F06 error.

If all checks ok, then its a faulty CCU that needs to be replaced. Here is the part.

Posted on Oct 20, 2012

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is error code F06


The "F06" fault code indicates a drive motor error. This means the control is unable to properly detect motor speed and the machine will shut down.

Mar 17, 2016 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

What does Error code F06 mean


Try this:
Possible Causes / Procedure1. Verify the shipping system including shipping bolts, spacers
and cables are removed.
2. Unplug washer or disconnect power.
3. Check wire harness connections between the drive motor and
the Motor Control Unit (MCU), and between the MCU and the
Central Control Unit (CCU).
4. Plug in washer or reconnect power.
5. Check the MCU by looking for operations of the drive motor.
6. Check the drive motor for powered rotations.

Read more: http://forum.appliancepartspros.com/washer-repair/11384-front-load-maytag-what-error-code-f06.html#ixzz33vFGkt1n
http://forum.appliancepartspros.com

Apr 23, 2014 | Maytag Dryers

1 Answer

Flashes error code F06


Check the wire harness that goes to all your connectors on the Motor, MCU, and CCU. I have seen a loose wire connector do this F06 error.

If all checks ok, then its a faulty CCU that needs to be replaced. Here is the part.

Oct 19, 2012 | Sears Kenmore Elite 4.2 cu. ft. Front-Load...

2 Answers

Indesit 123 FAULT F06


I had this error and engineer said the meaning of the codes on the web are wrong as they don't like to disclose their real code meanings for pure protectionism reasons. F06 on IWD7145 is a burnt out door interlock IDC error. He replaced the part number C00085194 (replacement door interlock) and microritardator part number 085194 and it works ok now.

Sep 06, 2012 | Indesit W 123 Front Load Washer

1 Answer

F06 Error Code


"F06" is a Motor Speed Error. The following link explains:

http://www.fixya.com/support/r714929-f06_error_whirlpool_duet_kenmore_elite

Read through the link provided and let me know if you have questions. In most cases this problem is attributed to a tachometer failure on the Motor Control Unit (MCU). If the this is the case, the MCU must be replaced.

If you require additional assistance, let me know. I hope you find this information helpful.

Sep 11, 2009 | Kenmore Elite 45986 Front Load Washer

1 Answer

Kenmore Elite he3t model 11045972404


POSSIBLE COMMUNICATION PROBLEM BETWEEN MAIN AND MOTOR CONTROLLER

Nov 22, 2008 | Kenmore 3.8 cu. ft. HE3 Front Load Washer

2 Answers

Whirlpool AWM 8023 -error F06


This erroe code means drive motor tackometer error Probably a bad motor or motor drive pc board or cable problems

May 23, 2007 | Whirlpool AWM8163 Front Load Washer

Not finding what you are looking for?
Dryers Logo

Related Topics:

586 people viewed this question

Ask a Question

Usually answered in minutes!

Top Maytag Dryers Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3056 Answers

Brad Brown

Level 3 Expert

18519 Answers

Are you a Maytag Dryer Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...