Question about Fishing

Open Question

Can I get a maintenance manual for a Daiwa Procaster Magforce PMF 53H

Found discarded, needs oil and/or greese. Need to know how to disassemble and reassemble for maintenance purposes.

Posted by Frank Hunter on

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Have had generator in storage, Makita G1300R. What do I need to do repair wise to get it to start after about ten years in storage??


Remove air filter assembly. Disconnect fuel line from carburetor and drain old fuel into suitable container to discard. Fuel Shut Off in the On position. If fuel has gelled up in the tank or lines, add small amount fresh fuel in fuel tank, swish around several times and flush until clean.
Loosen and remove Carb Mounting nuts, throttle linkage and spring (note the position). Carefully remove Carburetor and very carefully remove gaskets (do not discard until completion of final reassembly)
Disassemble Carburetor and thoroughly clean with appropriate cleaner and immediately following with compressed air. If thick gelled old fuel is present, soak disassembled carb in cleaner overnight before using compressed air is highly recommended.Reassemble carburetor, replace gaskets and install Carburetor (Reverse dis assembly) Inspect and replace air filter upon reassembly.
Inspect spark plug and replace (do not over tighten).
Add fresh fuel and perform start procedure. Initial start might take a few pulls but should start right up.

Sep 23, 2014 | Garden

1 Answer

I need a detailed schematic of a 1990 ford f250 steering wheel column that includes directions for disassembly and reassembly


Go back to the dealer ,chat the storeman up nicely and he will print you off the parts picture so you some idea where it goes ,this vehicle is so oil that nothing is complicated about this motor as i repaired a 350 1989 model last week and apart from getting the plugs out after they had been in for 15 yrs their was nothing i found difficult ,just big and heavy with its twin rear wheels and a complete brake rebuild as well .Still think a ford transit diesel is a better motor though because at our fuel prices here in europe ? need i say more

Mar 30, 2012 | 1990 Ford F250

2 Answers

The foot pedal on my Singer Inspiration is stuck on fast speed.


Hi lawoffice474...

Unplug your foot pad from the machine and the electrical receptical.
Try moving the foot pedal with your hands, back and forth as if you were pressing your foot on it.
Did it loosen up?
If yes then you still need some maintenance...
If no then you still need some maintenance.
Disassemble the foot pedal and take as many pictures as you need to be able to reassemble it.
Once you have disassembled then you will look to oil (one drop max) the pivot points of the foot pedal, like the hinge assembly, reostat linkage,etc.
Once you have it oiled then try moving the foot pedal again my hand before reassembly.
If everything moves ok then your good to go...
Reassemble the foot control.
If not then its time to replace it with another foot pedal such as one of these at this webpage below:
Please take time to rate me thumbs up.

http://www.sewingmachinesplus.com/singer-foot-controls.php

Sep 10, 2011 | Singer Inspiration 4206

1 Answer

REplaced belt ok but pulleys look out of alignment - any remedy?


You need to disassemble parts and then reassemble them properly.use greese oil for better performance

Mar 12, 2011 | Hotpoint First Edition FEW12 Front Load...

1 Answer

I am giving my 1995 marzocchi dh3 forks an over haul and need to know everything about fork oil level, air pressure, sag setup, how to disassemble and reassemble all seals I have no owners manual


This is for the 1996 Model. Unless there was an earth-shattering change, it should do the Trick; http://my-sport.spb.ru/manual_1/1996%20dh3.pdf

Nov 08, 2010 | Cameras

2 Answers

I have a Miele silver moon that kept shutting off while using it. I replaced the hose with the new 125-s model but problem came back. It does appear to be a problem with the hose. Any suggestions?


My S558 Red Velvet had the same problem. I disassembled the handle and cleaned the rings and electrical contacts. The problem has not come back.

Sep 28, 2010 | Miele s558 Silver Moon Vacuum

1 Answer

I had asked Fixya Maytag Dryer expert about a chirping noise.


When he siad to use oil he may have tried to get you to figure out what was causeing the problem. If you oiled each bearing one at a time you would have found out exactly where the noise was comming from, Then you would have to see it the bearing was bad? or could be lubed with a greese gun and see if it would last. This is a common way to trouble shoot so you don't buy all the parts that you oiled, so if you know which part made the noise use a heavier oil or a synthetic greese to lube the part and see if it works. If it does not it coust you nothing for parts or labor except your own. A Service Tech would have charge $80.00 just to come out plust parts and labor. So now you know what part is defective so if you need more help Just ask!

Jul 09, 2009 | Dryers

1 Answer

Loose gearshift


INSPECTION 1. Inspect the bushing for wear or damage. 2. Inspect the return spring for damage or deterioration. REASSEMBLY 1. Apply multi-purpose grease to the sliding parts of the bushings. 2. Reassembly is reverse of disassembly. INSPECTION 1. Inspect the bushing for wear or damage. 2. Inspect the return spring for damage or deterioration. REASSEMBLY 1. Apply multi-purpose grease to the sliding parts of the bushings. 2. Reassembly is reverse of disassembly.8fa5804.jpg

Apr 24, 2009 | 2003 Hyundai Santa Fe

1 Answer

Disassembled the stapler now need diagram to reassemble


Found user manual online but no parts breakdown, I have a phone number at 1-800-343-9329 and they might be to email you the breakdown. Wish I had better info but this is all they furnish online.

Mar 15, 2009 | Stanley Tools & Hardware - Others

1 Answer

Rebuilding a Avertec 3150 HS


Dear User, How far have you gone into rebuilding this laptop? What do you have and what do you need still to attach? Let me know. I might be able to sent you a maintenance manual.

Jul 17, 2007 | Averatec 3150H Notebook

Not finding what you are looking for?
Fishing Logo

Related Topics:

1,001 people viewed this question

Ask a Question

Usually answered in minutes!

Top Fishing Experts

ray gallant

Level 3 Expert

69825 Answers

Andrew Taylor
Andrew Taylor

Level 3 Expert

34473 Answers

Steve P
Steve P

Level 3 Expert

3712 Answers

Are you a Fishing Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...