Question about Bunn 10 Cup Home Coffee Brewer

Open Question

Bunn gr10-b need a new fill tray plastic has eroded at the large nut are there replacement parts available? Part number on tray 33514

Posted by Anonymous on

Ad

5 Related Answers

Anonymous

  • 1 Answer

SOURCE: Bunn B10-B leaks

I used Foxhollowrun's solution and went to my local hardware store (Menard's). You can purchase 3/4" Hole Grommets typically found in the electrical department. The brand I purchased was Gardner Bender Model GHG-1575 3/4" Hole Grommets. Here is all that you need to do (very quick and easy):

1) Break away the brittle pieces from the original hole in the resevoir.

2) Remove the old rubber / plastic washers - I found I didn't need them. However, hang onto your metal washer that the drain screw goes through.

3) Slip the 3/4" grommet around the hole.

4) Place the original metal washer on top of the grommet.

5) Screw the drain screw back into the heater which will seal the grommet via pressure. Be sure not to over tighten it - I just snugged mine up.

6) Put everything back together, rinse several pots of water through it, check for leaks, and you should be good to go.

As Foxhollowrun indicated, you may need to tighten the drain screw a bit if you do have a leak. I lucked out - it worked the first time. I believe it cost me about $2 to fix. Also, I did not need any caulk. If you do use caulk, I was told you need to use food-grade caulk.

One last note - as Foxhollowrun indicated, the grommets are quick thick which is why I removed all of the old washers. The original metal washer is just thin enough to allow the drain screw to be reinstalled.

Thanks to Foxhollowrun for a great remedy!

Posted on Mar 23, 2010

Ad

atbsmmom

  • 189 Answers

SOURCE: bunn code date 145000 water leak took apart need

If you will call customer service, a seal repair kit can be sent to you which is successful 90-95 percent of the time in fixing the leak problem.

Posted on May 19, 2010

Ad

atbsmmom

  • 189 Answers

SOURCE: Bunn Coffee Filter Basket Tray Broken

If you will contact Customer Service at 800-263-2256 with the model and date code, they will be happy to help you. The tray assembling itself is not replaceable but the machine does carry a 3 year warranty.

Posted on May 19, 2010

atbsmmom

  • 189 Answers

SOURCE: hot water leaks out the bottom when filling

If you will call 800-352-2866 with the model and date code and we will be able to help you resolve your issue.

Posted on Jul 02, 2010

atbsmmom

  • 189 Answers

SOURCE: I have a Bunn GR10-B - date code 252602 - how do I

You can send it in with a check/money order and have the switch repaired. If you call customer service at 800-352-2866 we can provide you the address.

Posted on Jan 18, 2011

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bunn GR10 Coffee Maker


Check bunn.com for free download of manual(s)
Call your vendor for service. Especially if this equipment is on loan from them,
Aloha, ukeboy57

Apr 06, 2014 | Bunn GR10 Coffee Maker

1 Answer

Water seal between the cold water tray and the heater unit is bad, where can I get a new silicon water seal


The seal is not available. I fixed mine by coating each side of the old seal with aquarium grade clear silicone sealer - about 1/16" thick.
Re-assemble and allow it to cure for 24 hours.

Jun 30, 2011 | Bunn GR10 Coffee Maker

1 Answer

My Bunn Omatic is leaking around the bottom onto the counter when I pour water into the well. I took the top off and removed the washer and seal to clean. The white plastic of the well hole looks to me...


The washer (gasket) is a tray seal. It's made of silicone. The gasket should be assembled by placing the screw nut into the tray (pan) then slip the white rubber gasket over the nut (under the tray) and gently screwed onto the top of the tank. It should be snug down a bit more than hand tight. Sometimes the nut (a large hollowed out bolt that allows water to flow through) can get a bit corroded. Teflon pipe tape helps but if it still leaks then all those parts will need replacement as it's made with a soft metal that easily pits.
** Okay I've given you the inside scoop but really you should not be poking around in there. Call the your vendor for service.
* parts can be found at Bunn.com or any Resturant equipment supply as this is a very common part. You may be able to find a rubber washer that fits though I suspect the black rubber may leave an after taste. Stick with the red type or find a silicone pad and cut a washer to fit.
* Final - If you have this in an office. Check with your coffee vendor as they may fix it for you or give you a replacement. Doesn't hurt to ask around.
Aloha, ukeboy57

Mar 29, 2017 | Bunn Pour-Omatic Coffeemaker, 10 Cup White

1 Answer

Hot water leaks out the bottom when filling resevior with water of my Bunn coffeemaker GR10-B


If you will call 800-352-2866 with the model and date code and we will be able to help you resolve your issue.

Jul 01, 2010 | Bunn GR10 Coffee Maker

2 Answers

The part you pour the water in leakshow do i fix or get new part


I presume that you are talking about the plastic pour-in tray, as this is the cause of most of these brewers leaking. I have seen some people repair these using hot glue, but that is a very temp. solution at best. The best way to repair these is to replace that tray. Maybe try your local Bunn repair facility to see if they have a used one hanging around. You can find your local service center on a list at www.bunn.com

Nov 19, 2009 | Bunn BT10B Coffee Maker

1 Answer

Bunn GR10 has a hole in the panal where the water runs into the


The only place I know of that you might be able to find a replacement tray for this style of brewer is from your local Bunn repair shop IF they have a used unit laying around that died from something else. Bunn will not even send out these parts to their repair centers. Good luck!!

Feb 04, 2009 | Bunn GR10 Coffee Maker

2 Answers

Difficulty in inserting the plastic deliming tool in bunn coffee


try keeping pressure on it, and turn it around as you insert it. You are trying to go around a corner in the tubr, and sometimes it is hard to get it to go around the bend.

Feb 04, 2009 | Bunn GR10 Coffee Maker

4 Answers

My Bunn coffee maker is leaking water


Dennis Karlen supplies repair parts for this problem. You can find the various kits on his website

http://www.jneuhaus.com/appliance/karlen.html

There are other suppliers who sell two silicon washers and a stainless steel washer in kits, but they tend to run considerably more.

The rubber washer would degrade quickly due to the heat. You may be able to get by with a new silicon washer. Check your local (not national chain but local francisee) hardware store.

Feb 15, 2008 | Bunn GR10 Coffee Maker

Not finding what you are looking for?
Bunn 10 Cup Home Coffee Brewer Logo

Related Topics:

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Bunn Coffee Makers & Espresso Machines Experts

Kelley Hopper

Level 2 Expert

67 Answers

gbob59

Level 3 Expert

3063 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Bunn Coffee Maker and Espresso Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...