Question about GARDENA 875 5Liter Handheld Garden Pressure Sprayer With Shoulder Strap

1 Answer

The pumping handle is very tight and difficult to pump.How do I repair this?

Posted by Anonymous on

Ad

1 Answer

dietmar702

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 33 Answers

Open the cylinder that is inserted in the bottle, in other words, the pump mechanism. Often the rubber seal gets twisted which makes it difficult to pump, or no air is blown inside the container. Also add some ghrease to the rubber seal and the cylinder.

Posted on Jan 20, 2016

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Pump wont suction. Handle snaps back when pulled up


Top has a lock shaped like an X. It is difficult to turn but once the small protrusions at end of each arm of X snap out of locking holes the pump handle can be removed and the O-ring that produces the seal can be replaced into the grooved seat it fell off. To help keep it from happening again, just spray some water into the space around the handle shaft when the pumping action seems a bit strained due to the O-ring drying out.

Sep 04, 2012 | Gilmour 030P 1.5 Quart Indoor Hand Pump...

1 Answer

How do you refill roundup pump and go


The Pump N Go can be refilled with either the Roundup Super Concentrate or Roundup Ready To Use Plus Refill Bottle.

To refill the Pump N Go with the Roundup Super Concentrate (purple cap), add 6.5 fl oz of the Super Concentrate to container and slowly fill with water.

To refill with the Ready To Use Plus Refill bottle, just slowly fill the Pump N Go with the refill container.

We do not recommend using Roundup Concentrate Plus (red cap) to refill the Pump N Go because it has different active ingredients and different information regarding use around edibles.

To open to Pump N Go container, please follow the directions below:

Stabilize container by holding between your feet

While holding the pump handle push down slightly and turn left (the pump will be out of the locked position)

The first time it is opened it will be difficult to open because for shipping safety the top is but on very tightly at the factory.

If you have any further questions, please contact us at 877-465-5160.

Hilary @Roundup

Aug 29, 2011 | Roundup "" Weed & Grass Killer

2 Answers

I bought a serfas bike pump some time ago and am not sure how to attach it to the tyre. Whether the lever is up or down, it does not attach and slips easily when pumping. I seems wrong. please inform of...


generally you have to put the pump up to the nozzle and have the lever down then put the nozzle in tightly and then pull the lever up. If after several attempts it doesn't work the pump may be broken, as bike pumps generally break easy

May 03, 2011 | Serfas Cycling

1 Answer

Kenmore HE2. Won't drain. I have gotten the screws off and the panel removed. I see a large round white (I guess the pump/filter thing) with a straight plastic piece across the center. When I try and turn...


You are referring to the drain pump reservior. Yes, they can be difficult to remove sometimes as they have a tight seal. Before you attempt to go any further read through the following link on checking the drain pump:

http://www.fixya.com/support/r3574284-checking_the_drain_pump_on_a_front_loade

This may provide you with some helpful tips on how to avoid a mess of water coming from the wash tub, drain pump and lines.

If the cap will not come off, and has an open style handle, you can use a screwdriver for leverage. Place the screwdriver in the handle and CAREFULLY turn in a counter-clockwise direction to remove. If the handle is closed, I have found that a set of channel locks (looks like a large set of pliers) can give you the necessary leverage to pop the seal loose. Cover the teeth of the channel locks with electrical tape to prevent marring the pump handle. Again, exercise caution so that you do not break the handle off. Once you have the cap removed, use petrolium jelly on the rubber o-ring and seal the cap tight. The petrolium jelly will help keep the seal, but will make it easier to remove the next time you need to clean it.

If you have any questions, please post back and let me know. I hope this helps you.

Apr 29, 2010 | Kenmore HE2 Plus Front Load Washer

1 Answer

How difficult is is to change the water pump on a 2000 Chevy Silverado and are there special tools needed?


Hi, my name is Ben. I wouldn't call this a difficult repair, but it is time consuming. You may need a special tool to help you remove the water pump pulley.
Remove the air intake duct, remove the upper radiator shroud,remove the fan assembly, loosen the bolts on the water pump pulley a few turns before removing the serpentine belt, then remove the serpentine belt, now remove the water pump pulley, if it's a V-8 remove the lower radiator hose and thermostat housing,unbolt the water pump, if it's tight lightly tap it with a RUBBER mallet. Important, clean the gasket surfaces very well. apply a thin coat of RTV on both gasket surfaces and install a new gasket. On V-6 engines use a small amount of the RTV on the bolt threads. The rest in the reverse of removal. Once completed, refill with coolant and check for leaks, bring the engine to notmal operating temperature and turn the heat on high

Apr 06, 2010 | 2000 Chevrolet Silverado 1500

3 Answers

Fuel pump is it a easy fix


no, it is inside the fuel tank, this means the tank has to come out of the car.

Nov 17, 2009 | 1999 Pontiac Firebird

2 Answers

The door handle is loose and i cannot tight the screws i dont want to call a repair man why would they make it difficult to tight the door handle .it cannot be difficult something to make a dollar this is...


mine was the handle was loose on the door not the coil in the stainless problem . i will try and figure it out my self i will not pay to have the handle tighten

Apr 05, 2009 | Crosley CRFF16 15.9 Cu. Ft. Frost-Free...

3 Answers

Replacing oil pump on 93 Toyota Camry (5SFE) wagon


Dave the only item in the oil pan that has to do with the oil pump is the pick up screen and tube. The 5FSE IS A 2.2 four cylinder. The oil pump is driven off the timing belt. All you have to do is remove the front covers and replace the oil pump. You can get a Haynes repair manual and it will give you step by step instructions. Engine does not have to be removed. I don't think fischmilch has ever worked on this style engine. Most important item to make sure you do is replace the timing belt and water pump. Good Luck

Mar 09, 2009 | 1995 Toyota Camry

Not finding what you are looking for?
GARDENA 875 5Liter Handheld Garden Pressure Sprayer With Shoulder Strap Logo

Related Topics:

520 people viewed this question

Ask a Question

Usually answered in minutes!

Top GARDENA Garden Experts

Dennis Key
Dennis Key

Level 3 Expert

2481 Answers

john h

Level 3 Expert

23504 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a GARDENA Garden Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...