Question about Excalibur Televison & Video

1 Answer

Why is their blue LED lights blinking on the receiver to my Excalibur remote starter

Posted by Kirill Lukosavich on

Ad

1 Answer

ayden copeland

  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

You need to turn off the power to it for thirty seconds then plug back in

Posted on Feb 11, 2015

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Onkyo receiver tx Rn555 remote stopped working...batteries fine... light comes on remote but does not work


To test the remote to find out id the led emitter is working, use your cell phone camera to look at the led while you're pushing a button on the remote. If you see the led blinking, then the trouble is in the receiver. If you don't see the led flash, the remote is toast.

Dec 05, 2016 | Televison & Video

2 Answers

Why doesn't my neotv netgear remote no longer communicating with box?


What do the different Remote control front LED lights mean?
  • Blink blue color twice per second: Remote control has paired NeoTV PRIME and is trying to connect NeoTV PRIME.
  • Blink blue color once per second: Remote control is trying to pair the NeoTV PRIME.
  • Orange blinking: Remote control battery is low. Please replace a new set of AAA battery.
go to page 15 of the following document:

http://www.netgear.com/landing/stream/img/gtv-specs/GTV100_IG_25Oct2012.pdf

Sep 09, 2014 | Computers & Internet

3 Answers

Why is a blue light blinking on my HP TouchSmart 600-1120 Desktop PC?


If it is in the tray, right-click it, and you can probably see what it is.

Jul 02, 2014 | HP TouchSmart 600-1120 All-in-One PC Black

1 Answer

Excalibur remote starter


I have changed the batteries in my remote starter. It will light up but is not working at all to unlock the locks or start the vehicle. Is there some kind of reset that I need to perform???

Jan 17, 2014 | Vehicle Parts & Accessories

2 Answers

I think I messed up the remote programing.. When I press to lock the doors they do lock but the horn doesn't honk anymore.. The blue light on the dash does not light up either.. I can still remote...


If the led is solid blue when the key is out of the ignition that means your in valet mode. Which would disable the alarm, but not the starter.
Simply turn key to IGN position then back to OFF.Push the valet button which is on the antenna next to the led and the led should turn off.Close door on vehicle and lock vehicle.Siren should now chirp.
Cheers!!

Sep 16, 2011 | 5701 VIPER 5701 2-WAY ALARM w/REMOTE START

1 Answer

Remotes won't program! Installed Viper 5001 on my 2007 Kia Sorento. Triple checked wiring..all is good. Remotes won't program...no power to main unit. Yet, tested main unit and it has power. Any...


There are two constant 12 volt wires at the ignition on this vehicle: blue and green. The red power (with fuses) wires from the Viper should be connected to either of the two. The ignition wire is yellow. The pink wire from the Viper should be connected there. The accessories are orange and white. The pink with white from the Viper should connected to one and the orange from the Viper should be connected to the other. Please note that the Pink with white should be programmed to act as an accessory (off during crank). The starter wire is red and the purple from the Viper should be connected there. Also check for a good ground connection.

For programming:
Press and hold "f" until LED lights solid (approximately 10 seconds), then press and hold remote starter button(circle w/arrow) until LED blinks three times and the amber transmit LED lights up.
Now you have to enter the remote control learn routine: Turn ignition on, within ten seconds press and release control button on antenna then, press and hold control button while pressing the lock button on remote. System will respond (horn/chirp/flashing parking lights) when holding control button and when pressing lock button on remote.

Jan 17, 2011 | 5101 LE 1 Way Car Remote Starter System

2 Answers

Moved to a place with a 139.53975SRT1 Garage Door and Keyless Entry. Keyless entry stopped working and I cant get code to operate door. All remotes stopped working. Reset codes with Learn button,...


Try this method for programming. Press and hold the button down on the remote while you press and immediately release the learn button. Do this for each remote.

Have you replaced the battery in the keypad? Try this:

Locate the smart/learn button on the rear of the motor unit near where all those white wires go. Press and immediately release this and then walk over to the keypad and key in any 4 digit code you like and press enter.

Post back with your results.

Jan 14, 2011 | Sears Craftsman LiftMaster Chamberlain...

2 Answers

Pioneer PDP-r06xe 50 in. Plasma Television Problem. During a Rain Storm - a lightening strike in my loft - the save system it has protect several electronics, but when I try to switch on - the TV it turn...


when switch ON it blinks 7time blue led - then switch OFF by SELF and blinks 8time blue led. Of-course when it switch off by self the TV swap the led from blue to red but the blinking Blue led is on the Receiver (The switcher on the TV is never blinking)

May 22, 2010 | Pioneer PDP-4350HD 43 in. Plasma...

1 Answer

Need codes for rcr 460 remote


1. Manually turn on the component
you want the remote to control
(TV, VCR, DVD, satellite receiver
or cable box).
Note: If you press an invalid key
during the Manual Code Search,
the remote does not respond and
the LED indicator light does not
blink. If you do not press a valid
Manual Code Search key (TV,
VCR, DVD, SAT·CBL, ON·OFF,
GO BACK), the search times out
after two minutes. When the
search times out, the LED
indicator light blinks four times
and turns off. The last
programmed code under that
component key is retained.
2. Press and hold the component key
(TV, VCR, DVD, SAT·CBL) you
wish to program. The LED indicator
light turns on and remains on.
3. While holding the component
key down, press and hold the
ON·OFF key. The LED indicator
light turns off.
4. After holding down both keys
for three seconds, the LED
indicator light turns back on.
5. Release both keys. The LED
indicator light remains on.
Throughout the
programming of each key, be sure
to keep the remote pointed at the
IR sensor of the component you
are currently programming the
remote to control.
6. Press and release the ON·OFF key
repeatedly until your component
turns off. Each time you press the
ON·OFF key, the LED indicator
light blinks, and the next code in
the list is sent. This process
continues until all of the codes in
the Code Lists have been searched.
If your component turns off, you
have found the correct code. (If it
cycles through and the LED
indicator light blinks four times
and turns off, all codes have been
searched. The Manual Code Search
method is exited.)


Press Stop when TV turns off.

Mar 06, 2010 | RCA Universal Remote Control

1 Answer

Astra remote car starter problem


your remote starter is in valet mode, the door lock will still work but no remote start, try pressing the trunk button 3 times, if that doesn't work turn the ignition switch on and off 5 times

Jan 03, 2010 | Astra Car Alarm And Remote Starter,...

Not finding what you are looking for?
Televison & Video Logo

Related Topics:

322 people viewed this question

Ask a Question

Usually answered in minutes!

Top Excalibur Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76455 Answers

Cindy Wells

Level 3 Expert

6199 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you an Excalibur Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...