My 9100 lifefitness upright bike display gone off and when i pedaling and hold the start button the display light up and go off within 2 seconds

About This Video

Crank Arm Cover Removal and Replacement Video for the 95Xi LifeFitness Crosstrainer

• This video demonstrates how to remove and replace a Crank Arm Cover on a Life Fitness 95Xi Crosstrainer elliptical

Necessary Tools:

• Philips Screwdriver



• 5/32" Allen Wrench



• 2MM Allen Wrench



• T25 Driver



• T50 Driver

1. Remove the main shrouds as seen in the shroud replacement video



2. Remove the outer link cover as seen in the outer link cover removal video



3. Remove the pedal lever assembly (as seen in Sportsmith's Pedal Lever Replacement video) on the side where the crank arm cover replacement is needed



4. Remove the two bolts holding the crank arm cover in place, and remove the crank arm cover



5. Replace the parts in reverse order

LifeFitness 95Xi Crank Arm Cover Video Removal and Replacement

Drive Belt Replacement Video for LifeFitness 95Xi Crosstrainer Elliptical

• This video will demonstrate how to replace the Drive Belt on your Life Fitness 95Xi Crosstrainer



• Video can also be used for drive belt replacement on a LifeFitness 90x, 93x, or 95xe crosstrainer

Tools needed:

• Philips Screwdriver



• T25 Driver



• T50 Driver



• 2MM Allen Wrench



• 5/32" Allen Wrench

1. Remove the main shrouds as seen in the main shroud removal video



2. Remove the left outer link cover as seen in the Outer Link Cover removal video



3. Remove the left pedal lever assembly as seen in Sportsmith's Pedal Lever replacement video



4. Remove the two bolts holding the crank arm cover in place, and remove the crank arm cover



5. Walk the drive belt off the pulley and remove it from the unit



6. Install the new belt around the crossover shaft first and then walk it onto the pulley



7. Replace the remaining parts in reverse order

LifeFitness 95Xi Drive Belt Video How To Replace

Camaro

1998-01

To reset the "OIL CHANGE" light, press and hold the "TRIP/OIL RESET" button on the instrument panel for 12 seconds. When the light flashes and then goes out, the system is reset.


Corvette

1997-01

To reset the monitor after an oil change, turn the ignition on. Press the "TRIP" button so that the "OIL LIFE" percentage is displayed. Press "RESET" and hold it for two seconds. The word "RESET" should appear on the monitor, then "OIL LIFE 90%".


Impala,
Monte Carlo

2000-01

Turn the ignition to ON without starting the engine. Fully press and release the accelerator three times within five seconds. If the CHG OIL SOON lights two times, the system is resetting. Turn the key to OFF, then start the vehicle. If the CHG OIL SOON light comes back on, the system has not been reset, repeat the procedure. Follow this procedure to reset the GM Oil Life System using the DE 100 Series Radio. Turn the ignition to ACC or ON and the radio off. Press and hold the DISP button on the radio for at least five seconds until SETTINGS is displayed. Press the SEEK up or down arrow to scroll through the main menu. Scroll until OIL LIFE appears on the display. Press the PREV or NEXT button to enter the submenu. RESET will be displayed. Press the DISP button to reset. A chime will be heard to verify the new setting and DONE will be displayed for one second. Once the message has been reset, scroll until EXIT appears on the display. Press the DISP button to exit programming. A chime will be heard to exit programming. A chime will be heard to verify the exit.


Impala,
Caprice

1994

To reset the "CHANGE OIL" light, turn the ignition switch to the run position with the engine off. Access the reset button on the end of the instrument panel by the fuse block. Press the switch and hold it for at least 5 seconds.



Lumina,
Monte Carlo,
Impala,
Caprice

1996-00,
1996-99,
1995-96,
1995-96

To reset "CHANGE OIL" light, turn the ignition switch to the run position without starting the engine. Fully depress and release the accelerator pedal 3 times within 5 seconds. The light will flash and go out.


Corvette

1990-96

After an oil change, or when "CHANGE OIL" appears on the Trip Monitor, with the ignition on and engine off, press the "ENG MET" button (located on trip monitor) once. Press the "ENG MET" button again within 5 seconds. Within 5 seconds, press and hold the "RANGE" button (1990-1994) or "GAUGES" button (1995). The light will flash. When it stops flashing and goes out, the system is reset.


Chevrolet Suburban,
GMC Yukon XL,
Chevrolet Silverado,
GMC Trucks Sierra

2000-01,
1999-00

Turn the ignition key to the RUN position. Fully push and release the accelerator pedal 3 times within 5 seconds. If the CHANGE OIL SOON light flashes 2 times, the system is reset. However, if the light comes on and stays on for 5 seconds, the system did not reset. Repeat the procedure if the system does not reset.


Silverado, Sierra Trucks

1991-93

To reset the "CHANGE ENGINE OIL" message, turn the ignition key to the run position. Press and release the accelerator pedal three times within 5 seconds. If the light flashes for 5 seconds, the system is reset. Repeat procedure as needed.