Dishwashers Logo

Related Topics:

Question about Zanussi Dishwashers

2 Answers

My zanussi dishwasher zdt12011fa wont turn off and the pump is constantly running trying to remove non existant water! any ideas only started with this problem yesterday

Posted by Adam Pinder on

Ad

2 Answers

Steve Kelly

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Comment about tipping the machine backwards worked for me, Top man for that answer, Thankyou

Posted on Sep 01, 2021

Ad

Mike

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 435 Answers

Get a tech out there, as these appliances get more sophicated, they become nightmares its best to buy a basic model

Posted on Feb 08, 2015

Ad

5 Related Answers

Anonymous

  • 123 Answers

SOURCE: Beko Freestanding Dishwasher

Hi there ....this condition is ususally caused by a water leak into the sump of the dishwasher which activates a safety switch to run the drain pump..preventing the appliance from being used....Remedy...tip the dishwasher back in the head allowing excess water to exit from the sump...then with the door open check that the air vent lock ring is secure, thet the salt unit retaining ring is secure..and finally that the filter unit to base screws are secure...this done re-start and you should b fine

Posted on Jan 05, 2007

Anonymous

  • 5 Answers

SOURCE: No water running to dishwasher

I had this problem and almost tossed this thing out the window. The water stopped pumping into the washer but the cycles kept on going... HERES HOW YOU FIX IT!! In the front bottom right you see the mushroom shaped float..... on the underside of the dishwasher you see that is pushing down on a switch. Its a simple little switch but the plastic pin connected to the float is easy to knock off the switch witch always leaves it in the up position !!! this is telling the washing machine that it is full of water. Find a way to keep the plastic pin on top of the metal switch and this will fix your problem. I used tape with a small piece of paper to keep from sticking to the pine or switch!!

Posted on Aug 28, 2008

Anonymous

  • 1 Answer

SOURCE: ASKO D1986: Water pump running constantly

Solved by draining water from bottom pan.

Posted on Jan 19, 2009

Anonymous

  • 1 Answer

SOURCE: Zanussi ZSF 6161 Dishwasher with Error 30 Code

The light cover on the side is loose causing it to flood remove the side and tighten the light cover the tilt the dishwasher to get water out of the float tray. let the dishwasher dry out and you should be grand

Posted on Sep 06, 2009

joe_lishman

Joe Lishman

  • 192 Answers

SOURCE: Hi, my zanussi zdf221 dishwasher wont work, it

The outlet pump is triggered by the anti flood micro switch via the polystyreene float on the base of the washer. If any water for whatever reason (leaky pipe)is on the floor the machiene automatically switches to pump out mode and only works once the water and the cause is rectified

Posted on Jan 17, 2010

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

0helpful
1answer

My dishwasher is not getting hot and dishes are always wet

Check heater ( multi meter) if ok then pcb failure, sometimes just a dry joint on board
Jan 10, 2018 • Dishwashers
0helpful
1answer

My zanussi dishwasher zdt12011fa will not switch off and the pump continues to run, obviously trying to remove non existant water! any ideas??

Most dishwashers (especially built in dw) in the bottom has microswitch which is activated if water leaks and runs drain pump to prevent flooding.

Dado
0helpful
1answer

Zanussi dishwasher beeps once and end of cycle light flashes

Most likely your dishwasher finds fault.

Appliances without a display will show the alarms by a number of flashes of the LED "end of cycle".

For example: one flash = i10, two flashes = i20
..........and so on

So, count how many times LED "end of cycle" flashes and you will know the error code.

Dado

0helpful
1answer

Bosch classixx

your absolutely right, remove kick panel and check for leak/ water. if there is none you may need to replace the control
0helpful
1answer

Got a zanussi dishwasher zsf6160, lights working but none of the programmes are starting, not taking in any water?

if you can here the drain pump run at the start the fault is with the water valve or blockage in the side tank on the lh side. if you dont here the drain pump it possibly the heater thats down to earth. the electronics can detact it and not start the prog if heater faulty.
0helpful
1answer

Drain pump won't turn off

Hi,

The reason the drain pump continously runs is because it is trying to remove any water too avoid any further flood as there is a flood in the base of the unit which activates the float switch and constantly activates the drain pump until the water has gone. Isolate the unit at the power switch and remove the bottom panel under the door panel. Dry up the water as best possible with a towel. Run the unit again and check for any water leaks. You may just have over sudded the unit with too much detergent. Only use 2 teaspoons of powder. To start with while testing don't use any detergent. Good luck

Hope this helps.
3helpful
1answer

Hi, my zanussi zdf221 dishwasher wont work, it makes a noise and constantly empties, any ideas please

The outlet pump is triggered by the anti flood micro switch via the polystyreene float on the base of the washer. If any water for whatever reason (leaky pipe)is on the floor the machiene automatically switches to pump out mode and only works once the water and the cause is rectified
0helpful
1answer

Zanussi aquaius DE 6855, starts off ok ,rinses ,but then stops and wont pump the water out and the lights start to flash on and off. Any ideas

Either the exit hose does not reach a high enough point or the waste-pipe is blocked. I had this problem in both situations.
0helpful
1answer

Dishwasher

you have a small leak inside your dishwasher and the anti flood switch is making, this is what keeps your pump running constantly. try removing the bottom plate and drying it out also check the switch is not permenantly made
Nov 14, 2007 • Dishwashers
Not finding what you are looking for?

7,084 views

Ask a Question

Usually answered in minutes!

Top Zanussi Dishwashers Experts

Paul Carew

Level 3 Expert

3724 Answers

Geoffrey White
Geoffrey White

Level 3 Expert

3965 Answers

Marvin
Marvin

Level 3 Expert

85240 Answers

Are you a Zanussi Dishwasher Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...