Question about Measuring Tools & Sensors

2 Answers

My acurite model75321a1 does not tell out side temperature

Ive changed batteries and pushed rest botten

Posted by john mcdonald on

Ad

2 Answers

AcuRite

  • Level 1:

    An expert who has achieved level 1.

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Contributor
  • 20 Answers

We would recommend a reset of your Weather Station. Please verify that you are using a good-quality, standard alkaline battery, and follow the steps below.

  1. Remove the batteries from the outdoor sensor only.
  2. In the outdoor section on the main unit, there will be a "CH" and number 1-3.
  3. If on CH 1, press and hold the channel button on the back of the unit for 5 seconds.
  4. Press and release the channel button one time, it should show CH 2.
    • If it does not change to CH 2, repeat steps 4 and 5.
  5. Press and hold the channel button for 5 seconds.
  6. Press and release the channel button one time, it should show CH 3.
    • If it does not change to CH 3, repeat steps 6 and 7.
  7. Press and hold the channel button for 5 seconds.
  8. Press and release the channel button one time, it should return to CH 1.
    • If it does not change to CH 1, repeat steps 8 and 9.
    ***Regardless of what channel you begin on, clear out each channel by holding the channel button and return to CH 1***
  9. Reinstall batteries in the outdoor sensor.
  10. Press and release the TX button.
  11. Leave both units side by side for up to 30 minutes to gain a strong connection.
If you need any further assistance, please contact AcuRite Customer Support at 1-877-221-1252 or [email protected]

Posted on Mar 17, 2015

Ad

Tom Chichester

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Measuring To... Master
  • 57,303 Answers

I checked my Acurite instruction file and found it rather vague about this issue but based on my experience with a similar system I found that battery changes have to be made at the transmitter first, allowing time for the transmitter to begin sending temperature data. Also, the Acurite instructions suggest use of lithium batteries in the transmitter where extreme low temperatures are encountered. My experience has been that the transmitter stops working at low temperatures so the reading comes and goes depending upon the weather. Currently it is 20 degrees F outside headed for 5.

Posted on Feb 01, 2015

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why isn't outdoor temperature displayed?


Try repeating the initial set up procedure. Remove all batteries from outdoor and indoor units. Install known-good batteries in the outdoor unit. Allow time for the outdoor unit to begin transmitting data. Install known-good batteries in the indoor unit. You should see the outdoor temperature displayed.

Feb 09, 2016 | AcuRite Acu-Rite 00621 Wireless Weather...

2 Answers

Why can't I receive input from the outside sending unit?


Make sure that all the batteries are good!!
This procedure outlines the typical process to pair the sensor and base.
Base Station Battery Installation

·Remove the printed vinyl label from the LCD screen of the base station
·Position the remote sensor near the base station
·Open the battery compartment at the back of the base station and insert (2) AA batteries according to the polarity markings. Replace the battery compartment cover.
·Within a short time the RF signal icon (located to the left of the outdoor temperature channel indicator) will start flashing. This indicates that the base station is ready to pick up the RF outdoor temperature signal from the remote sensor. It will continue to flash for 3 minutes or until the signal from the remote sensor is detected.

Register the Remote Sensor
·Open the battery compartment at the back of the remote sensor and slide the channel selector switch to your desired channel. For the first remote you may select any channel, for additional remotes select any unused channel
·Insert (2) AAA batteries according to the polarity markings. Be sure to install the batteries in the remote within the time that the RF signal icon is flashing on the base station. 1541 WeatherGuide Wireless Weather Forecaster with Barometer

Jan 07, 2016 | Measuring Tools & Sensors

1 Answer

How to reset my Acurite 1099rx after replacing battery


http://www.acurite.com/advancedsearch/result/?q=1099RX

There is no reset button, installing new batteries causes the sensor to reset itself.

Try removing and re-installing the batteries.

Good luck,
Steve

Jan 15, 2013 | Measuring Tools & Sensors

1 Answer

I have an acu-rite 592w weather station and need to know how to remove the stand to change the batteries.


I know this thread is old, but I see no one answered the question - "How to remove the stand"

Grab the stand on the sides with your thumb on one side and fingers on the other and pull down ... I had to "rock it out" or pull one end then the other. It seems stuck but it will come off ... Another option would be to take a small screwdriver and insert it in the small openings under the standard gently push the tabs while pulling down on the side you are doing. Push the tabs towards the outside of the unit not the inside ... in other words if you are working on the left hole push left (left while viewing from the face of the unit)

Aug 05, 2011 | Acu-Rite AcuRite 00592A2 Wireless Humidity...

2 Answers

How to change battery in mouse?


hi
if there is any door open it
otherwise unscrew the screws in botten of mouse
check your mouse charging method

Jun 10, 2010 | Logitech Cordless Mouse

Not finding what you are looking for?
Measuring Tools & Sensors Logo

Related Topics:

616 people viewed this question

Ask a Question

Usually answered in minutes!

Top Measuring Tools & Sensors Experts

Brad Brown

Level 3 Expert

18438 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Tom Chichester

Level 3 Expert

57301 Answers

Are you a Measuring Tool and Sensor Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...