Question about Whirlpool Washing Machines

1 Answer

RE Whirlpool Mod WTW8200YW0 top load, there is always soap left on clothes in the washer no matter type and amount of detergent my wife uses. Any ideas?

Different types and quantities of detergent

Posted by Cal Cummings on

Ad

1 Answer

Dyron Webb

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Champion:

    An expert who has answered 200 questions.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Whirlpool Expert
  • 220 Answers

Check the water suppl lines to make sure they are not hooked up backwards the rinse cycle uses cold water if the temperature sensor detects hot water it will stop power to the log valve if hooked up correctly then place unit in a rinse cycle to see if rinse valve is opening

Posted on Jan 31, 2015

Ad

5 Related Answers

Anonymous

SOURCE: My Maytag Front Loading Washer Does Not Fully Rinse Cloths MAH8700A

A friend had this problem and was ready to buy a new machine. Sometimes it worked and sometimes not. I took a last look before new machine and found a coin that would intermittently block the pump/discharge port on the machine.

Posted on Apr 14, 2007

Ad
Krazytech

Franklin Ouchida

  • 725 Answers

SOURCE: Whirlpool Duet Front Load Washer

do a vinegar flush Pour a quart of distilled vinegar into your washer and using Hot water wash let your machine run through a wash and rinse cycle. The vinegar will cut through suds .. also wipe down the rubber gasket with a 1/2 vinegar /water solution to clean the gasket

Posted on Jul 21, 2008

Anonymous

  • 21 Answers

SOURCE: Clothes come out extremly wrinkled on top loding whirlpool washer

This is normal. You can try a lower spin setting or smaller loads. The wrinkles will come out in your dryer.

Posted on Jan 19, 2009

Anonymous

  • 31 Answers

SOURCE: What does F- indicate?

The SD code, is a sudsing code. If you are using the appropriate amount of soap and HE soap, it could be a communication error with the sensor and the CCU (the main control board). If you take off the panel on the bottom of the front (3 screws on the bottom hold it on). Once you get in, there is a plastic pouch on the right hand side there is a tech sheet that will have a list of all the error codes, and what to check.

Good luck

Posted on Feb 12, 2009

blueextc3221

blueextc3221

  • 15935 Answers

SOURCE: I have a Whirlpool Duet washer WFW9500TW.

F35 is a water level error.
The water level switch (pressure switch) has malfunctioned.

If you remove the top panel, three screws in the back, you will have access to the pressure switch.

With the tub empty, remove the vinyl hose from the switch and blow backwards through the hose to clear any restrictions.

If the fault codes return after doing this, you will likely need to replace the pressure switch.


Also - please be sure to use He soap.

Thanks for using FixYa - a 4 THUMBS rating is appreciated for answering your FREE question.$$$$

Posted on Sep 28, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

White streaks on dark clothes


The white streaks are of soap build up on your machine tub. You can get ried of that by putting cascade dish washing soap in your washing machine and run full cylece , with out clothes.

Apr 13, 2013 | LG WT4801CW 3.7 cu. ft. top load washer

1 Answer

Soap suds on the door at the end of a wash cycle. Miele E526


With all modern front loading washers, you might find that the amount of detergent you need is much less than what is recommended by the detergent makers!

First, be sure you're using the He (High Efficiency) detergent and try using only 2 or 3 tablespoons of detergent. If you've heavily stained clothes, be sure to pre-treat them rather than adding more detergent. That should also help with the extra soap left in the clothes after a complete wash cycle.

Give this a try and adjust the detergent as needed to get the best results for your situation.

Hope you find this Very Helpful and best regard!

Sep 22, 2009 | Miele Novotronic Premier 500 Front Load...

2 Answers

My bosch does not always completely wring the clothes out at the end of the cycle causing me to have to put the clothes through another wash. Has anyone had this problem?


...at the end of the wash, I then set the dial to DRAIN, then press start.  I wait for a special drain cycle to run.  Then, I set the dial to SPIN, and wait for a special spin cycle to run.  The clothes are much dryer and spun out after this process.  I'm not happy with the washer, it came with my new condo.  BUT, I'm trying to learn how to use it.....

Aug 23, 2009 | Bosch Axxis WFL 2060 Front Load Washer

1 Answer

Not enough water per load and suds


if you use washer without cloth you will some water and it is normal..use different detergent and use less you will be ok..hope that help you.

Jun 19, 2009 | Whirlpool Duet GHW9150P Front Load Washer

2 Answers

Kenmore 80 series washer leaves soap residue on clothes no matter


After speaking with someone with trouble shooting experience in these matters, I now believe the problem lies NOT with the washer but with a bad batch of laundry detergent which fails to dissolve properly in the water.  

Mar 12, 2009 | Kenmore 22422 Top Load Washer

1 Answer

We have a Whirlpool top loader Washing Machine in top order. I have tried various powders but always get powder "stains or scum" on items that have been washed. I use the "warm" cycle...


use what ever detregent you want try pretreating strians and heavey soiled items with shout. use recommended amount of soap and try not to overload your washer too many clothes will displace the amount of water in tub and also put strain on your washer which could cause failure

Dec 16, 2008 | Washing Machines

2 Answers

How much detergent that is not HE can I use?


It is strongly recommended that you DO NOT use regular detergent in an HE washer. The regular detergent is formulated for a wash tub capacity of 35 gallons. A High Efficiency washer, such as yours, only uses 5 to 7 gallons of water per load. You can potentially cause premature failure of the gaskets and seals, as well as drain pump problems by using a higher concentration of detergent. In addition, you may end up with residual soap left retained in your clothing which can cause skin irritation. So...if you do the math, you would have to use about 1/5th the amount of soap you would normally use. However, if this is a new washer, you will void the manufacturers warranty if it discovered that you purposely used improper detergent. There is a disclaimer in the Owner/Operators Manual that should explain this. I hope you find this information helpful.

Nov 13, 2008 | Whirlpool Duet GHW9150P Front Load Washer

1 Answer

Soap left in clothes


hope you are using he detergents (high effeciency low suds) also if you have soft water oversudsing can occur even with he ..try reducing amount ..also have been told tide he detergent tends to suds more so may try switching detergent brands try runing washer with no soap no clothes begore next load to flush out any detergent that may remain ..be sure to run washer with bleach no clothes on short cycle peroidically to avoid mold/mildew odors that front loads tend to acquire after a few months use and leave door open if possible between uses..let me know about detergent thanks

Jul 15, 2008 | Kenmore 44102 Front Load Washer

1 Answer

Leaves soap residue


theres a new product just hit hte market www.affresh.com try this stuff speciffically designed for the frontloaders and endorsed by whirlpool, makers of your machine

Apr 01, 2008 | Kenmore Oasis HE 27062 Top Load Washer

1 Answer

Could SOAP DISPENSER be caked with soap???


POWDERED DETERGENTS GET CLOGGED ALOT IN THOSE DISPENSERS. I ADVISE CUSTOMERS TO FILL THERE WASHER AND ADD SOAP WHEN IT STARTS TO AGITATE WHEN USING MORE THAN A 1/2 CUP OF POWDER ... THEN ADD YOUR CLOTHES ... THE WASHER HAS A SAFTEY SWITCH WILL STOP MOST WASHERS WHEN AGITATING OR IN SPIN CYCLE,SO YOU CAN LOAD CLOTHES ... OTHER THAN THAT ... ALL YOU CAN DO IS KEEP THAT DISPENSER FLUSHED OUT WITH HOT WATER AFTER EVERY WASH. JUST POUR HOT WAYER TROUGH IT ... IF THE WATER BACKS UP (EVEN WITH A SLOW POURING) THE DISPENSER IS PLUGGED AND NEEDS TO BE FLUSHED OUT WITH A HOSE. GOOD LUCK AND STAY DRY !!!

Apr 29, 2007 | Whirlpool Calypso GVW9959K Top Load Washer

Not finding what you are looking for?
Washing Machines Logo

Related Topics:

98 people viewed this question

Ask a Question

Usually answered in minutes!

Top Whirlpool Washing Machines Experts

Marvin
Marvin

Level 3 Expert

85239 Answers

Michael Thomas
Michael Thomas

Level 3 Expert

3053 Answers

Brad Brown

Level 3 Expert

18397 Answers

Are you a Whirlpool Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...