Question about Light Office Equipment & Supplies

1 Answer

Ultima65 laminator wont heat

Unit turns on and runs forward and rev. but no heat. Power and ready light come on but heat light never comes on. Usually blinks while heating up.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 827 Answers

I would look for a fuse first, then it might be a heater problem

Posted on Jan 23, 2015

Ad

1 Suggested Answer

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a GBC Ultima 65 Laminator and the lamination is not adhering. The materials I am laminating are coming apart.


Are you letting the laminator reach operating temperature? If the ready light is on and it is not getting hot then you may have a problem with the temp. sensor. Put your hand near, but not on, the top roller to feel if it is getting hot. Don't touch the roller in case it is hot. If it is getting hot then wait for the ready light to illuminate(about 10 minutes).

Feb 14, 2017 | Gbc Office Equipment & Supplies

1 Answer

Why won't my laminator turn on?


There is a heating unit inside of a hot laminator. Sometimes when you use this machine for too long it can damage some of the internal components because most of those things are full of plastic. You may want to see if Fellows can take it back under warranty. If they can't you are going to have to get a new one.

Feb 05, 2017 | Fellowes Office Equipment & Supplies

1 Answer

Why is my GBC Ultima laminator beeping?


It will beep when you turn it on to acknowledge power. It will also beep when it reaches ready condition. Your laminator has safety switches for the lower feed tray and upper heat shield. Any time the upper shield is lifted the power is shut off. When you lower it down the power is turned back on, causing a beep. The same is true for the lower feed table. When it is removed and then re installed the machine beeps. These are safety features so that the laminator doesn't turn on when you are reloading it or unjamming it. Check that the safety switches are fully engaged if you get unnecessary beeping.

Oct 25, 2016 | Gbc Office Equipment & Supplies

1 Answer

Laminate did not come out it just went back inside on roller


warm the machine back up, get the glue sticky again, then work it off, either by going in forward or reverse, whichever works best for the given situation. Don't use anything sharp as the rollers damage easily....very expensive

Sep 09, 2014 | Gbc Heat Seal Ultima 65 Laminator 1710740

1 Answer

How do I feed New laminating film through straight? Top roll of new film is wrapping around bottom heat roller


go to youtube and watch the video on GBC ultima65 film loading. sounds like you are not using a threading card to load laminator. Manila File folders work great to load laminators Westco Laminating Svcs 405-324-6092

Aug 30, 2014 | Gbc HeatSeal Ultima 65 Laminating System

1 Answer

Scotch Thermal Laminator not heating up.


well it sounds like you may have cut a wire or pull one somewhere. i would go ahead and take it apart carefully and check everything. may have unplugged something hopfully! let me know whwat happens!

Jan 31, 2014 | 3M TL902VP Scotch 9" Thermal Laminator...

1 Answer

Laminator won't heat up


This is just rediculous. Where's the friggin answer?
Mine won't even come on. JUNK!

Jan 28, 2014 | Gbc HeatSeal Ultima 65 Laminating System

1 Answer

GBC Pinnacle27 Laminator has no control board power


Each heat shoe has a small thermal fuse, if either fuse is blown, the laminator keypanel will not operate. 99% fix everytime, just follow the wires from each heat shoe (right side of laminator) cover off. Ohm each set of wires and look for an open circuit. replace fuse (TCO) and it will work everytime......Westco Laminating Service 405-324-6092.

Jan 08, 2014 | GENERAL BINDING CORPORATION Laminating...

1 Answer

My gbc creative laminator won't heat up


We have an Ulitma 65 and it won't heat up...Any suggestions on how to fix this? We are at a school and no $ to replace the whole unit. Thanks in advance.

Mar 29, 2013 | Office Equipment & Supplies

Not finding what you are looking for?
Office Equipment & Supplies Logo

Related Topics:

237 people viewed this question

Ask a Question

Usually answered in minutes!

Top Light Office Equipment & Supplies Experts

Marvin
Marvin

Level 3 Expert

85206 Answers

Brad Brown

Level 3 Expert

18110 Answers

Copy-Tech

Level 1 Expert

9 Answers

Are you a Light Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...