Question about RCA RT2360 System

1 Answer

Overload When ever I turn it on the display screen says overload then it shuts off.

Posted by redneckdaddy on

Ad

1 Answer

Anonymous

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 319 Answers

Circuit problems. Take to pro/tech for check out

Posted on Apr 22, 2008

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Receiver


If the display shows overload, you are playing it too loud, or have too many speakers connected. Overload is a protection method used to shut down the unit, before it's damaged.

May 31, 2014 | Audio Players & Recorders

Tip

My Pioneer displays Overload


Overload is displayed when the amp draw is excessive, and can be caused by different faults.
when Overload is detected, the protection circuit will shut down the unit to prevent further damage.

The first thing to try is hard reset. Shut down the unit for about one hour to drain power completely.
This can fix minor problems that can cause overload, for example electrostatic charge accumulation on internal capacitors.

If that does not fix the problem, then you must find the fault.

Overload can be caused by shorted speakers, wrong impedance speakers, or by a contact on speakers wiring.
Check speakers connection and test different speakers with 6, or better 8 Ohms impedance.

Another test can be done by unplugging all speakers, and reconnecting and testing them one at a time, at a very low volume.

If the speakers are OK, then preamp, shorted input/output connectors, main power supply or faulty output transistors can draw too much amps causing overloading.

In that case it is recommendable contacting Pioneer at the number listed on the owners manual.

on Jun 22, 2009 | Pioneer VSX-D608 Receiver

1 Answer

Display shows overload and receiver shuts down


This means that one (or maybe more) of the amplifiers is shorted. Remove all speakers cables and try again. If you get the same message that means that one (or more) amplifiers is fried. To find which and why you will have to open the unit and test the amplifiers.

Jul 31, 2010 | Pioneer VSX-D412 Receiver

1 Answer

Display flashes


you might have a flyback problem! also check the abl circuit .

May 07, 2010 | Samsung SyncMaster 753S 17" CRT Monitor

2 Answers

Protection overload and the system shuts off


Reasons: 1. Short in the wire, speaker, or amplifier 2. Amplifier malfunction 3. Overload of the amplifier 4. Overload of the speaker
Listening to audio at loud levels requires more power obviously. But the speakers and amplifier may not be rated or capable to handle it due to age or design.

Jan 13, 2010 | Cambridge Audio Azur 540R Receiver

2 Answers

Overload on screen


Check the speakers maybe one is already about to burn

Aug 21, 2009 | JVC RX-7010V Receiver

1 Answer

VSX-D608 Overload and shutdown


Overload is displayed when the amp draw is excessive, and can be caused by different faults.
when Overload is detected, the protection circuit will shut down the unit to prevent further damage.

The first thing to try is hard reset. Shut down the unit for about one hour to drain power completely.
This can fix minor problems that can cause overload, for example electrostatic charge accumulation on internal capacitors.

If that does not fix the problem, then you must find the fault.

Overload can be caused by shorted speakers, wrong impedance speakers, or by a contact on speakers wiring.
Check speakers connection and test different speakers with 6, or better 8 Ohms impedance.

Another test can be done by unplugging all speakers, and reconnecting and testing them one at a time, at a very low volume.
No more than two 4 Ohms speakers can be connected to the unit, or you will get overload.

If the speakers are OK, then preamp, shorted input/output connectors, main power supply or faulty output transistors can draw too much amps causing overloading.

In that case it is recommendable contacting Pioneer at the number listed on the owners manual.

Jun 22, 2009 | Pioneer VSX-D608 Receiver

1 Answer

RCA RS2531 display says Overload and won't function


Start by disconnecting the speakers, turn the volume to minimum, and see if the unit still shuts down. You might have a shorted speaker or wire. If the trouble continues, either the amplifier integrated circuit has gone bad, or some other component failure is activating the shutdown. I can't suggest any specific parts you might check because many things can cause the same symptoms. You'll need to have the unit looked at by a commercial servicer.

Feb 20, 2009 | RCA RS2531 CD Shelf System

1 Answer

Turns off when i turn it up


Does it power back up after it shuts down, if it does power back up it is unlikely it is an internal fuse, you would need to replace the fuse if that was the issue, could be an amplifier overload, check the demand your speakers require in watts, and be sure the right ohm speakers are being used, many receiver will display "overload protection"and shut down, and some just un-power to prevent a electical short from occuring.

Feb 02, 2009 | KLH R3100 Receiver

1 Answer

"Overload"


Check your wires for cross polarity

Dec 20, 2006 | Technics SA-DX940

Not finding what you are looking for?
RCA RT2360 System Logo

Related Topics:

284 people viewed this question

Ask a Question

Usually answered in minutes!

Top RCA Audio Players & Recorders Experts

ThaMp3Doctor
ThaMp3Doctor

Level 3 Expert

8597 Answers

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

The Knight
The Knight

Level 3 Expert

76390 Answers

Are you a RCA Audio Player and Recorder Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...