Question about Electrolux EW1000i Front Load Washer

1 Answer

E4 error code on electrolux washing machine ewt 854s

Not draining during wash cycle

Posted by on

Ad

1 Answer

E4 is the pump is blocked {not running} pehaps a hair pin or clothing wires get stuck
fully drain it and take the filter out

and clean it


these error codes are similar to candy
youll get an idea from this video
https://www.youtube.com/watch?v=kzhlvB2LjXg

Posted on Nov 28, 2014

Testimonial: "Thank u very much simeon"

Ad

5 Suggested Answers

tina gallow

  • 123 Answers

SOURCE: Need Manual for Electrolux EWT 13420 W - EWT 10420

These site carries the full line of Electrolux Manuals
http://userguides.50webs.com/manual.htm

Posted on Sep 06, 2009

Ad

Anonymous

  • 1 Answer

SOURCE: Electrolux ewf1087 washing machine error code?

what is a (e40)

Posted on Jan 02, 2010

Anonymous

  • 1 Answer

SOURCE: check hose error on electrolux wave touch washing machine

I'm sure nojallo1 has already fixed his but I just ran into the same problem and didn't find anything in my searches for a solution. The problem I had was the test cycle wasn't long enough to get hot water through my water lines so it could verify the hot and cold hoses were in the proper places. Solution: Turn the hot water on in all the sinks in your house until they have hot water running through them. This will prime your hot water line so it is full of hot water instead of cold water. Then run the install cycle again and it should be fine.

Posted on Jan 21, 2010

john_cross

  • 6277 Answers

SOURCE: electrolux washing machine ewt 1330

Hi from retired Englishman in SW France,
(no promises but try this!)
I would gently suggest as a first step that you clean the drain motor/pump lint tray/filter. So many 'faults' are caused by blocked filters and many machines will not even go to rinse or spin or release the door lock if there is any water still left inside.
Here are my complete and generic guidance notes for checking both the drain motor filter and the drain motor ;-0)
If you are unsure where the filter is, it is often behind the front lower (kick) panel (or in some machines at the rear in an awkward position!). These panels are either held on by (plasic) screws or will just pull off. Most filters are held in by a round cover/knob. Sometimes the filter will not come out with the cover and you will have to persuade it to come out to play.

REMOVE POWER AND ENSURE YOU HAVE A WATER RECEPTACLE/RAGS TO SOAK UP THE WATER WHICH IS BOUND TO POUR OUT (alternatively use a wet vac as sensibly suggested by VinnyB1234!)
It's surprising what people have found in theirs! It is always worthwhile checking it on a regular basis.
Now- whilst the filter is removed it is normally possible to see the drain motor and ensure it is not jammed by a foreign object such as a needle or a toothpick. It should be able to be turned by hand/finger- the power IS OFF!
At this point it is also possible to test if the motor works. No clothes or water in the machine, select a spin cycle and put the power back on. You should be able to see the motor turning at some point, possibly straight away. Using something suitable like a glove see if it is easy to briefly slow the motor down. If it is easy then the motor is malfunctioning.

If this has assisted you please consider a 4 thumbs up for the rating.
Thanks and good luck!
John C

Posted on Jul 13, 2011

Duarte Nunes

  • 69 Answers

SOURCE: problem with electrolux washing machine

draining pipe its too low. check this link:

http://applianceguru.com/washers/drain-min.jpg

Posted on Aug 27, 2012

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Samsung front load washing machine model wf42h5000a. During rinse cycle machine stops and displays error code e4 and Cannot be reset.explain error code. What are possible solutions ?


hi Judi.
this is what i found.

If your Samsung washing machine is displaying a E4/error code on the control panel after completing the spin cycle and the clothes are still wet, we've got the solution for you. This fault is most commonly caused by an unbalanced washing machine load.

Samsung Washing Machine E4/UE Error Code ' eSpares

https://www.espares.co.uk/advice/symptom/samsung-washing-machine-e4ue-error-code
What does 4e mean on my Samsung washing machine?This is essentially a fill timeout error which will normally mean that either the water isn't on or that an inlet valve has failed or pressure switch problem check pipes as well. Water fill time out: The washing machine has failed to fill with water in a reasonable time.24 Nov 2015Samsung washing machine error code 4E and E1 Fault Not filling in ...https://www.youtube.com/watch?v=cFlnxeB0P0gSearch for: What does 4e mean on my Samsung washing machine?
or try this link.
Samsung front load washing machine error code e4 Google Search

Nov 27, 2017 | Samsung Washing Machines

1 Answer

How to fix E4 in electrolux front load washing machine


this might help: http://laundry.manualsonline.com/support/other/washer/e4-errorits-not-draining-always-e4-appears-in-th-5582230

Mar 13, 2015 | Electrolux Washing Machines

1 Answer

Electrolux washing machine ewt goes straight to drain


Check your drain hose. It may be too far into the drain pipe. 6 to 8 inches max

Sep 24, 2014 | Washing Machines

1 Answer

Electrolux ewt 10410W


HEATING ELEMENT RELAY FAULT... THAT'S ERROR CODE ON YOUR MACHINE

Dec 27, 2013 | Washing Machines

1 Answer

CODE E4 ELECTROLUX EWT64S FULLY AUTOMATIC WASHING MACHINE


In my experience, E4 is appear when spin is starting. Then I check the 'magnetic door safety switch' and gotcha, I find the problem --> 'magnetic door safety switch' is damage (always open). Because some reason, I am short-circuit it. Fixed.

Oct 11, 2012 | Washing Machines

1 Answer

I have an error code "EF" for my Electrolux


Generally, EF error is showed with an additional number on your display... EF 1, EF 2, EF 3, EF 5, EF8, or EBF.
Each error code will depict a different cause and solution. Out of these solutions, the most common is the control board and possibly the UIB (User Interface Board), or too higher mains voltage coming into the house, causing damage in this UIB device.
Test and check voltage, if this isnt solve it, relace UIB device.
Hope this helps.

Mar 05, 2012 | Electrolux EW1200i Front Load Washer /...

1 Answer

How to reset my washing machine (electrolux)


my electrolux EWT606 will not spin. it drains and then just wont go into spin cycle....no error messages it just beeps. can anyone help me please as i have kids with disabilities and NEED to wash!

Mar 14, 2009 | Electrolux Washing Machines

Not finding what you are looking for?
Electrolux EW1000i Front Load Washer Logo

1,524 people viewed this question

Ask a Question

Usually answered in minutes!

Top Electrolux Washing Machines Experts

Gerry Harvey
Gerry Harvey

Level 3 Expert

1481 Answers

Poppa Maddo
Poppa Maddo

Level 2 Expert

372 Answers

Brad Brown

Level 3 Expert

18166 Answers

Are you an Electrolux Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...