Question about Video Game Consoles & Games

1 Answer

IZE FUSES GO INTO A BALLY STRIKES AND SPARES PINBALL MACHINE

WHAT SIZE (AMP AND VOLT) FUSES DO I NEED FOR THIS MACHINE

Posted by DORIS I SIXMA on

Ad

1 Answer

FixIt_Right

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 171 Answers

There are several fuses. All are 3AG size. On the Rectifier board you need:
F1=10 Amp 32V
F2=3/4 AMP, 250V SLO-BLOW
F3=4 Amp, 32V
F4=5 Amp, 32V
F5=20 Amp, 32V
F6=3 Amp, 32V SLO-BLOW

On the solenoid driver board you need:
F1=3/16 Amp

Posted on Dec 06, 2014

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hi. I have a 1964 Happy Tour Bally EM Pinball Machine. This is basically the same as the Grand Tour machine. It won't reset.


Hey Bill, if you have facebook, look up Tilt (Bar in toronto canada). the owner may be able to help you if you message him.

Jan 14, 2017 | Video Game Consoles & Games

1 Answer

Hello. I have a centaur II pinball and I'm having trouble with the machine not shooting out any balls. And the targets dont pop back up. Can u help?


The two most common problems with solid state pinball machines are blown fuses and bad connectors. A third common problem is leaking batteries that eat away the copper traces on the motherboard. I assume that you have checked all of the fuses. You can try to unplug and replug each cable connection in the backbox. This can sometimes clear intermittent contact problems. In other cases metal fatigue within the connector make for poor contact and the connector may need to be repinned. Also stress on a male connector pin can sometimes cause cold solder joints. Many solid state machines had rechargable battery packs that were soldered onto the motherboard. Over time these would leak acid onto the motherboard and cause issues. If none of these suggestions seems to help then I suggest that you pose your question on an active pinball forum like www.pinside.com. There are many people there that can help you debug the problem.

Nov 14, 2016 | Video Game Consoles & Games

1 Answer

My whitewater pin keeps on blowing fuse F114. display read check fuses F114/F115. Changed 114 but keeps on blowing.


Pinball problems are commonly discussed on pinball forums. For your case go to http://pinballbash.com/forum/index.php?topic=2526.msg23570#msg23570 and look for a very long append from VisitorQ. He gives a nice detailed description of the possible causes.

Aug 22, 2016 | Game Room Guys Flipper Opto Board Williams...

1 Answer

My mr and mrs pacman pinball machainght flipper not working what should I look for?


Bally uses an end of stroke blade switch for their flippers. Lift up the playfield and look for the blade switch associated with the right flipper. If there is a wire off or they are broken then resolder it or change them and it will be fixed. If you don't see any problem then put a jumper across the connection and see if it works. DO NOT LEAVE IT ATTACHED. If it worked then change the blade switch. Other possibilities are a bad solder connection on the Solenoid driver board or a bad flipper coil itself. Hope this helps

Dec 07, 2015 | Video Game Consoles & Games

1 Answer

Jandy Lite 2 LJ pool heater FL4 Fuse amp size


if blown they are 220 volt 3 amp you can also remove them

May 20, 2015 | Jandy Pool & Spa

2 Answers

All balls shot out


I need to know what machine are you working on? Different era machines have different answers.

Feb 08, 2014 | Bally/Midway/Williams Video Game Consoles...

1 Answer

What is the standard size of a pinball ball?


the standard size is 1 1/16" there are some machines that use smaller balls you can check online for what size you should use for your particular machine.

Oct 03, 2013 | Video Game Consoles & Games

2 Answers

Im looking for a 1978 bally's fireball manual


Bally made Fireball in 1972 and 1976
They made Fireball II in 1981 and
Fireball Classic in 1986
some of the manuals can be downloaded for free
from the net just search IPDB on the web

Aug 10, 2013 | Video Game Consoles & Games

1 Answer

Bally coin slot machine wont let the handle pull


THIS IS DOCTOR FIX. MY BUSINESS IS GAMING REPAIR. (JUKE BOX=PINBALL= SLOT MACHINES
BOWLING =POKER, FOR 68 YEARS.) IF YOU HAVE NOT SOLVED YOU PROBLEM, I ASSUME IT IS ELECTRONIC, NOT MECHANICAL. IF MECHANICAL , LET ME KNOW, I WILL TELL YOU WHAT TO DO.
ON THE ELECTRONIC, OR ELECTRIC (NO COMPUTER)
THERE IS A BAR MOVES ON TO THE CAM ON TOP OF THE CATCH, ABOUT 3 INCHES ABOVE THE BOLT THAT HOLDS THE ARM IN PLACE, WHEN A COIN IS INSERTED INTO THE COIN SHOOT, THAT METAL BAR ENGAGES THE RATCHET , TO SPIN THE WHEELS. DOES THAT HAPPEN ON YOUR SLOT.? OPEN THE DOOR PULL THE WHITE SWITCH THAT CLOSE WHEN DOOR IS CLOSED (OUT) THESE ARE A THREE POSITION SWITCH.
IN-HOME JUKE BOX REPAIR
[email protected]

HOPE IT HELPS.

May 03, 2009 | Bally Walk In 9 8"" X 19 3"" X 7 6"" high...

Not finding what you are looking for?
Video Game Consoles & Games Logo

Related Topics:

949 people viewed this question

Ask a Question

Usually answered in minutes!

Top Video Game Consoles & Games Experts

Muntejaya Ginting
Muntejaya Ginting

Level 3 Expert

10422 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Brad Brown

Level 3 Expert

18403 Answers

Are you a Video Game Console and Game Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...