Question about Konica Minolta Bizhub Press C6000 Copier

1 Answer

What is c2704 in konica minolta c6000

Gives an erropr code c2704 on powering. i need to know what does it mean

Posted by Pastory Zacharia on


1 Answer

Philip Hughes

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    Visited the website for 3 consecutive days.


    An expert who has answered 20 questions.

  • Expert
  • 80 Answers

I think that is the code for the black charger unit. It might be the charger itself or a board problem. Make sure the black charger is seated correctly.

Posted on Nov 01, 2014


5 Related Answers


  • 1 Answer

SOURCE: proplem with KONICA MINOLTA bizhub C450


Posted on Nov 10, 2008


Norman J Weimar Jr

  • 6960 Answers


Check your bypass tray, the tray is on the right side of the machine, the tray flips out for legal and 11x17 paper sizes. Check that there is nothing jamed inside, code says that the tray can't lift. so check for anything jamed inside down there. As to reset the code open then close the front door where you put the toner. Turning the machine on and off will not reset the code. but open and closing the front door will clear about 80% of the service codes.

Btw, I’m available to help over the phone in case u need at

Posted on Jul 25, 2009

SOURCE: IError Code C13FO on konica minolta Di1610

C13F0 - Laser error
The laser output exceeds the upper limit value.
The laser output remains lower than the lower limit value.

Posted on Aug 23, 2009


  • 1 Answer

SOURCE: Konica Minolta Magicolor 4690MF gives 0502 error.

machine trouble 0092 service call
This happen after I cleaned the waste box for Konica Minolta Magicolor 1600W

Posted on Mar 08, 2010


amir hamza

  • 318 Answers

SOURCE: Solution for error code c2557 konica minolta bizhub 250 machine

ADTC sensor failure

Posted on Aug 07, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do i reset the error code c2704 in konica minolta press c6000/7000

Thread 2704

Abnormality in the black charging unit.
Possible causes:
Black charging unit
HV Unit
Print Control Board

Best guess is that you have a faulty charge unit. Try swapping the units around with another colour and see if the fault code shifts.

Nov 01, 2014 | Konica Minolta bizhub Office Equipment &...

1 Answer

91 geo metro all new parts will crank but no spark

insert the ECU diagnostic connector (DLC) jumper.
crank for 5 seconds. release key, watch the CEL lamp flash codes.
do you get DTC erropr for the CMP sensor?

which engine>? 1.0L
here is the page that shows HOW TO DO THAT.
this is and OBD1 car, with a jumper check.
all cars , if the precursors to spark fail, sets a code. (error)

Sep 29, 2014 | 1991 Geo Metro

1 Answer

Erropr Code 91.720.00.4380

launch phaserSmart on the support page on can troubleshoot it online....good success, meder's tv service

Jan 23, 2013 | Xerox Phaser 8560DN Laser Printer

1 Answer

Need to know what the "reduced engine power' MIL

this is one of two things, first theres a problem with the engine , the way it runs its loosing power or if the wheels spin and the computer picks it up then it will reduce the power to avoid wheels from slippping, this is like when driving in the snow, now if the check engine light is coming on with this message then you have a problem and the first thing to do would be to have the codes pulled and see what codes are stored. what happens is the computer sees a problem and turns on the light and stores a code for that problem. for example there may be a code that reads po300 multiple misfires. this code would mean the computer has seen the motor misfiring and with some testing the problem can be found. there are many auot part stores that will scxan the computer for free and give you a read out with the code. if you get the codes i can help you further, have a good day.

Mar 18, 2011 | 2004 Pontiac Grand Prix

1 Answer

Red light on power pack

red light means you need a new one also it can becaused by the xbox not geting enogh power check connetions if that dont help you can look at the error code the xbox gives you thats about it because you need alot of know how this thing works to find the problem

Dec 27, 2010 | Microsoft Xbox 360 Console

1 Answer

Clp-510 constantly gives paper jam error, although none exists.

false error message / could be due to the dirty rollers or bac=d sensors on the printer. Sometime when printer does not get enough power it might give this erropr message .
Hence also try to change the power source.

Oct 16, 2010 | Samsung CLP-510 Laser Printer

2 Answers

Do you know the meaning of dot in mt. ember?

Those dots are BRAIL format used by the blind - you will need to buy a game guide to decode the meaning of the dots - OR you can do it yourself by looking for a brail decoder:
here's one

Aug 22, 2009 | Nintendo Pokemon FireRed for Game Boy...

2 Answers

Jvc th-s8 no sound

There is a stock fault on the sub woofer unit.
R2702 fusible resistor is likely to be faulty.
Here is their modification - dodgy english but you get the idea.

Reasons: R2702 (QRZ9005-470X) a 47 Ohm 1/4W resistor is open circuit due to rush current at the time of
power supply ON/OFF.
Cure: 1) R2702 change value : QRZ9005-470X --> QRJ146J-220X
2) C2704 change value QETN1EM-107Z --> QETN1HM-476Z

Sep 28, 2008 | JVC TH-S8 System

Not finding what you are looking for?
Konica Minolta Bizhub Press C6000 Copier Logo

Related Topics:

530 people viewed this question

Ask a Question

Usually answered in minutes!

Top Konica Minolta Office Equipment & Supplies Experts

Norman  J Weimar Jr
Norman J Weimar Jr

Level 3 Expert

6960 Answers


Level 1 Expert

51 Answers

George Mclaughlin

Level 2 Expert

369 Answers

Are you a Konica Minolta Office Equipment and Supply Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides