Question about Samsung WF337AA Front Load Washer

1 Answer

Washer was running fine got to the spin now won't to anything DB appeared on the screen and it kept beeping

Posted by Anonymous on

Ad

1 Answer

Sal De

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Samsung Master
  • 2,699 Answers

It's from an unbalanced load,you can try unplugging it or kill power to the washer forlike 10 minutes to reset the computer board and hopefully this will do the trick,i've never seen this code,i goggled it and found it's from an unbalanced load.hope this helps

Posted on Oct 21, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My washer was washing, but then it kept beeping thae sceen says db out of balance tryed to open the door to move the clothes around but door will not open,it's stuck on this cycle


Not sure if you have already figured this out or not, but it may be necessary to shut off the machine or unplug it to get the access you need. I have a Kenmore front load and there are some cycles other then spin, that will not allow you to stop and open the door - water in the drum and washing is one of them.
I have not had to try to open my unit but the above is what I would be trying if you have to get the door open. If the washer is still going, then maybe try to ignore the alarm beep and let it go until it gets to a stage where you can interrupt the cycle

May 22, 2017 | Washing Machines

1 Answer

Tricity Bendix AW1260W - drum won't turn - 5 beep error repeats


Washer motor control board failure is the likely problem, also check all connectors for signs of burning. Also test the washer motor.

Apr 24, 2017 | Tricity Bendix AW1260W Front Load Washer

1 Answer

My laptop has a green screen on start up


Green Screen? Never heard of that, normally its a Blue Screen if there is a problem.

Give us more details on what happens when you hit the power button. Does anything appear on the screen? Do the laptop try to boot? Any lights, beeps, fans running, hard drive spinning?

Apr 07, 2012 | Computers & Internet

1 Answer

Maytag stacked unit LSE7806ACE. dryer is fine , the washer will not fill or run, if I manually turn the timer to drain the tub spins and the lid switch works fine. But the unit won't do anything f


You have a timer problem, the contacts are welded in spin mode.
This is almost always caused by advancing the timer by hand when the dial is pulled out in the "ON" position, causing arcing of the contacts.

Sep 22, 2017 | Maytag LSE7806A Top Load Stacked...

1 Answer

Kenmore washer 80 series stopped draining


So it will agitate and fill but the motor won't run during drain and spin?
If so, the likely cause is a bad lid switch. The paddle that the probe hits when the lid is down moves a small switch. That switch can do two things
1. fail internally. It will look fine outside but it won't close the circuit
2. the screw holes snap and it hangs off the wires, the probe no longer hits the paddle and the switch stays open.
The lid switch is cheap and very easy to repair.

Nov 10, 2011 | Kenmore Washing Machines

1 Answer

Washer says f26 and won`t spin the clothes out. is there anything i can do?


This error code indicates that the door needs to be opened and closed.
The F26 code may appear the first time you try to use the washer. Open and close the door to clear the display.
The F26 code may also appear if the washer has run three cycles without the door being opened. Open and close the door to clear the display.
If opening and closing the door does not remove the error display, press Pause/Cancel twice.

The above procedure is the specified way by whirlpool technicians to clear the error code.

Feb 02, 2011 | Washing Machines

2 Answers

I have a GWL11 Fisher Paykel washer. It was running fine then it was beeping and had stopped-- the spin light was the only one left on, although water is in it. Basin looks lower than I recall. It won't...


Hi just read you posting.Now when the machine was beeping was the spin light the only light that was on while it was beeping?If this is the case then my manual tells me your Motor Controller is faulty and needs replacing.Please confirm which light was on when the machine was beeping because the motor controller module is not cheap.Looking forward to your reply.

Jun 28, 2010 | Fisher and Paykel GWL11 Top Load Washer

1 Answer

Fisher & Paykel Ecosmart will Wash but not Rinse/Spin


You have too many clothes in the washer. Take some out and try again

If you need further help, reach me via phone at https://www.6ya.com/expert/dan_73bbd84fe1d95b61

Sep 09, 2009 | Fisher Paykel EcoSmart GWL15

Not finding what you are looking for?
Samsung WF337AA Front Load Washer Logo

254 views

Ask a Question

Usually answered in minutes!

Top Samsung Washing Machines Experts

The Knight
The Knight

Level 3 Expert

76584 Answers

Brad Brown

Level 3 Expert

18665 Answers

Cindy Wells

Level 3 Expert

6259 Answers

Are you a Samsung Washing Machine Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...