Question about Hotpoint RGB745 Gas Kitchen Range

Open Question

Gas burner won't light. It "clicks", but there is no spark.

Posted by Anonymous on

Ad

2 Suggested Answers

6ya6ya

6ya staff

  • 2 Answers

SOURCE:

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Anonymous

  • 116 Answers

SOURCE: Top right burner on hotpoint gas range doesn't light

there is a spark ignition in the middle between the front and back burners....one for the left side and one on the right side. When it was cleaned i bet that the spark ignitor was slightly bent towards the front burner...now the gap is too big to fire the rear burner...the ignitor is very similar as the spark made in those push down lighters. so its safe to play around and adjust them as needed to make them work...Go ahead and take it apart and tinker with adjusting it...until you get both front and rear burners running again the way it was before.( peek at the otherside as a reference and try to make it match)
I hope this helps you out a little bit 8-)

Posted on Jun 06, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Electric spark will not work, burners will not light


The spark electrode sends a spark to ignite the gas in the burner assembly. If the spark electrode is defective or worn out, it might not produce a spark, or the spark might be too weak to ignite the gas. As a result, the spark electrode will make a clicking sound when the burner is turned on, but the burner won't light. If the spark electrode is defective, replace it.

I’m happy to assist further over the phone at https://www.6ya.com/expert/latoya_8ed1bf3dc615c15d

Mar 25, 2018 | Magic Chef Kitchen Ranges

1 Answer

Viking range burners won't light


from I review I found it might be this...Simple replacement of Glow Bar igniter requires removal of entire front panel with many screws
so sounds like your igniter might be shot - it heats up to ignite the burners - easy fix - get a long torch lighter and just light the gas after turning it on -

Nov 05, 2017 | Viking VGIC485-6G Gas Kitchen Range

1 Answer

I have a maytag gemini gas stove three igniters work but won't light the burners. One igniter won't spark


Replace the "igniter switch assembly". The igniter's are getting a weak spark and since you have one that will not spark at all, this is the usual problem. Here is the assembly to order.




The part comes with a 365 day, any part, any reason return policy.

Nov 12, 2012 | Maytag MGR6772BDS Gemini Gas Kitchen Range

1 Answer

Burners won't light


That clicking is the igniter trying to spark. Turn on the burner and attempt to light it with a match. If you know gas is comming out, you will most likely have to replace igniter.

Sep 26, 2012 | GE WB13T10045 Gas RanOven Igniter Glowbar...

2 Answers

The thing that lights the burner won't stop clicking.


Hi,
Here is a tip that I wrote that will help figure out why the burner spark keepson clicking...

Gas Range Repair Burners Keep on Clicking
heatman101

Aug 30, 2011 | Maytag 30 in. CSG7000 Gas Cooktop

1 Answer

Gas grill wont lite manuallly


Do you mean it won't match light or the ignitor won't spark and light the burners? Or both?

If it won't match light or the ignitor sparks, but the burners don't light, that means you're not getting gas to the burners.

Check to the tank valve and make sure it's turned ON. Also, make sure that there's gas in the tank.
If both of those check out as OK, turn the gas tank valve OFF. Disconnect the hose from the tank and wait 5 minutes. Reconnect the hose to the tank and turn the tank valve ON VERY, VERY SLOWLY (Slow motion, slow). Once the valve is fully open, light the burner farthest from the tank first and turn it to HIGH. Did the burner light and the flame height looks correct? If so, light the remaining burners following the same procedure. Now, are they all lit and the flames heights look correct? If so, you solve the problem. Just remember to always open the tank valve very, very slowly.

if the burners failed to light. Remove and clean all the burners, as well as the venturi valve on the open of each burner. Spiders like to build nest in the venturi valves.

if cleaning the burners did not solve the problem, you will need to replace the grill's hose/regulator assembly. You can find it in any home center or hardware store that sells gas grills and accessories, for about $30.00. Take you old one with you for comparison purposes.

Hope this helped you troubleshoot and solve the problem. Please be kind enough to let me know. Thanks and Happy grilling!!

Jun 10, 2011 | Weber SPIRIT E-210 (NG)

1 Answer

I have a gas stove top but today all four spark igniters started sparking all at once an now won't turn off even when all knobs are in the off position


Hi,
Here is a tip that I wrote that will help figure out why the burner spark keepson clicking...

Gas Range Repair Burners Keep on Clicking
heatman101

May 14, 2011 | Kitchen Ranges

1 Answer

I have a magic chef oven model # 61S04PAW. the


Electric gas igniters sometimes get stuck in one position causing a clicking sound. The clicking sound that you hear is the electric arc that is pulsing from the igniter conductor (wire) to ground (the gas burner). It receives power from the electrical outlet that the stove is plugged into.
Residue from food and sometimes cleaning products may be preventing the igniter from producing a spark (Arc) to the base of the burner. This is a common problem that occurs when the stove has been cleaned or food is allowed to build up. Make sure that the igniter and the burner base are clean and dry. This will help with proper operation. Oven cleaner and a small tooth brush may be used to accomplish this. Another problem with ignition may occur if you have too little (touching) or too much space between the igniter and the base of the burner; it will prevent the burner from igniting. You should only have a little more space than the thickness of a nickel between the burner base and the igniter. A good “blue” arc from the igniter to the burner base is optimal. If this doesn’t work, you may need to replace the electric igniter module. Good luck.

Jul 07, 2010 | Magic Chef 31000 Gas Kitchen Range

2 Answers

Ge profile gas range. one burner with no clicking and no ignition


You may have a bad burner switch. If you turn one of the other burner switches to make the spark modules spark look and see if the electrode is sparking at the bad burner. Most of the spark modules send a spark to all 4 burners when activated. If it sparks when another burner is activated open the valve and see if the burner will ignite. If so you probably have a bad burner switch.

Jan 10, 2010 | GE Profile Spectra JGBP90 Gas Kitchen...

1 Answer

Burners ignite simultaneously (clicking)


When you set a burner to light, all burners spark. This is normal. Move knob back off the spark position as soon as burner lights. All sparking will stop.

Sep 04, 2008 | DCS 48 in. CP486GDSS / CP486GDSSL /...

Not finding what you are looking for?
Hotpoint RGB745 Gas Kitchen Range Logo

Related Topics:

99 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hotpoint Kitchen Ranges Experts

Ismael Rodriguez...

Level 2 Expert

184 Answers

John Tripp
John Tripp

Level 3 Expert

4656 Answers

Cindy Wells

Level 3 Expert

6063 Answers

Are you a Hotpoint Kitchen Range Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...