Question about Televison & Video

1 Answer

WHERE CAN I GET A MANUAL FOR A TENSORVISION MAX FSF402BR FLOOR LAMP WITH NATURAL LIGHT FOR MY LOW VISION. IT HAS NOTHING TO DO WITH A TELEVISION! IT IS A LAMP MADE BY TENSOR CALLED VISION MAX # IS FSF402BR

Posted by Marion Schreiner on

Ad

1 Answer

Thomas Beaver

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 2,119 Answers

I wasn't able to find their web site. The suspected website is for sale and I found that the inventor has died. It may be that it is no longer being made under that name.
This is a link for ordering replacement bulbs.
Tensor Corporation BULB ORDER FORM Free Online Doc

Posted on Oct 15, 2014

Ad

Add Your Answer

×

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What does code 888 mean


I have not seen that code on these pool heaters. You might want to check in the owners manual and follow their troubleshooting flow chart to find the source of your problem.

http://www.backyardcitypools.com/images/bwp/Max-E-Therm-Manual.pdf

Jul 02, 2010 | Sta Rite Sta-Rite Max-E-Therm Low NOx Pool...

1 Answer

I turn the tv on it stay on for one second then it goes off thats when the lamp button comes on its red. then the red light comes on and it stays on although the tv is off the red lamp light is still on


Your lamp timer may be maxed out which means you should change the lamp and reset the lamp timer. When the timer max's out it won't turn on till it is reset.

Feb 09, 2010 | Mitsubishi WD62327 TV

1 Answer

Ihave a Philips 50PL9126D tv and I just replaced the lamp because the picture was very dark. I can see the picture but it is still somewhat dark, bright in the middle,dark at the edges. I tried to adjust...


Sounds like you may have the wrong lamp. Make sure you purchased a Philips lamp that's 100% compatible with your television model. Philips pioneered that lamp, so naturally they make 100 different types for DLPs and LCD projections.

You may have an elliptical lamp instead of parabolic. The lamp for your TV should read P22h.

Feb 04, 2010 | Philips Televison & Video

1 Answer

The TV does not work and the red and green light flash together


This could mean your lamp is bad or your lamp timer is max and needs to be reset. Check your manual to see what the blinking lights mean.

Jan 16, 2010 | Toshiba 46HM95 46" HDTV

1 Answer

My blank screen, red flashing light projection tv


Most likely the lamp has failed. The red light will blink with a pattern (number of flashes then a pause) You can refer to the users manual for information as to the nature of the problem by the aforementioned pattern.


Cheers

Jan 15, 2010 | Toshiba TZ43V61 43" Rear Projection...

1 Answer

Red blog and bubble vision, after lamp change.


YES, CHECK WITH HITACHI THEY ARE REPLACING SOME OUT OF WARRANTY LIGHT ENGINES

Dec 11, 2008 | Hitachi 50V500 50 in. HD-Ready LCD...

1 Answer

Correct voltage for lamp connection?


(Lamp may light and go out) suspect bad lamp part # 915P020010 2. Check for 12-volts DC at J-9 connector pin 4 on the Engine Driver PCB, if missing check for an open F9A09 on the Power PCB, if it is open replace F9A09 part # 283P127060 and the Light Engine part # 939P977020 3. (Lamp may light and go out) Check for 5-volts DC at J-9 connector pin 1 and 2 on the Engine Driver PCB if low or missing check C9A37 and C9A38 both 3300 UFD 10 V part # 181P732040 on the Power PCB (part # 930B921002) 4. At power on the lamp turns on and off three times and then the unit shuts down with a red lamp LED (lamp error). Replace the Light Engine part # 939P977020 5. Lamp enable line at J14 pin 6 does not switch to 5 volts after turn on, 12 and 5 volt supplies are good. Suspect the Light Engine part # 939P977020 6. Lamp enable line at connector J14 pin 6 on the Engine Driver PCB switches to 5 volts after turn on and does go to 0-volts (low) after 5 seconds, 12 and 5 volt supplies are good. Suspect the Lamp Power PCB (ballast) part # 939P978010 7. Lamp enable line at connector J14 pin 6 on the Engine Driver PCB switches to 5 volts after turn on but does not go back to 0-volts (low) after 5 seconds, 12 and 5 volt supplies are good. Suspect the Light Engine part # 939P977020 .

Oct 06, 2007 | Mitsubishi WD-62725 62" Rear Projection...

Not finding what you are looking for?

Open Questions:

Televison & Video Logo

Related Topics:

119 people viewed this question

Ask a Question

Usually answered in minutes!

Top Televison & Video Experts

The Knight
The Knight

Level 3 Expert

76466 Answers

Cindy Wells

Level 3 Expert

6220 Answers

Marvin
Marvin

Level 3 Expert

85239 Answers

Are you a Televison and Video Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...